12 |
user manual made by KR-sabers and Dmitry Shtok
emergency_voltage
– voltage in millivolts, a value between 3000 and 3700. If this parameter is missing or ignored, it takes the default 3500. Please note
certain components on the circuit board have a minimum operational voltage of 3V. So please be sure to not leave the
emergency_timeout
parameter
for too long. It’s default to 180 seconds.
emergency_timeout
– time in seconds the voltage is below
emergency_voltage
. If ignored it takes a value of 10 seconds.
When the battery drops below
emergency_voltage
for the time indicated by
emergency_timeout
, then the board will enter automatically in low-power
(deep sleep) mode. If the LEDs are ON (strip or HBLED) then a retraction effect is executed before entering in low-power.
clash_sensitivity
– is a value between 100 and 500. If this value is 0 or the parameter is not present, it will be set automatically to 300.
Higher value - less sensitive.
selection_wheel
– has three values. Each number represents:
blade colour
selection wheel,
blade profile
selection wheel and
font
selection wheel).
0 = disabled, 1 = enabled. This allows you to customise which menus you would like to have available when operating the saber.
selection_axis
– two axes which define the selection wheel orientation. Each value can be
1
,
2
, or
3
representing
x
,
y
or
z
accelerometer directions.
For example:
selection_axis = 1,2
would use the
x
and
y
axis so you would cycle the menu like using a motorbike throttle.
Fonts Section
(
maximum 16 fonts)
[font#]
– the section describing font number N. Each font should have its own section.
font_name
– name of the font folder in the SD card.
font_type
– describes the type of font. It can be:
monophonic
– for a monophonic font
polyphonic
– for a polyphonic font
smoothswing
– for a smoothswing font
sampling_frequency
– is the sampling frequency of all the sounds in a given font. The only two possible values are:
sampling_frequency = 22050
sampling_frequency = 44100
smoothswing_threshold
–
is valid only when font_type = smoothswing
, degrees/second needed to register as a swing.
smoothswing_sensitivity
–
is valid only when font_type = smoothswing
, swing sensitivity, degrees of rotations per second required to reach full volume.
smoothswing_sharpness
–
is valid only when font_type = smoothswing
, non-linear swing response, higher values makes it more non-linear.
smoothswing_hum_ducking
–
is valid only when font_type = smoothswing
, how many percent the hum sound will decrease as swing increases.
smoothswing_max_volume
–
is valid only when font_type = smoothswing
, swing volume multiplier defaults to 3x normal volume.
smoothswing_transition1
–
is valid only when font_type = smoothswing
, length of first transition in degrees.
smoothswing_transition2
–
is valid only when font_type = smoothswing
, length of second transition in degrees.
accentswing_high_threshold
–
is valid only when font_type = smoothswing
, degrees/second needed to register an accent swing.
A higher value means a faster swing is need to start an accent swing.
accentswing_low_threshold
–
is valid only when font_type = smoothswing
, degrees/second needed to end an accent swing.
A lower value means the accent swing will continue longer as the swing slows down.
hum_gain
–
is valid only when font_type = smoothswing
, percentage to scale the hum sound by increments of 100. A higher value makes the hum louder.
A lower value makes the hum quieter. hum_gain = 100.0 keeps the original volume.
Effects Section
last_used_color
–
do not change.
This is set automatically. This allows the board to remember the last used colour before shutting off.
last_used_profile
–
do not change.
This is set automatically. This allows the board to remember the last used profile before shutting off.
last_used_font
–
do not change.
This is set automatically. This allows the board to remember the last used font before shutting off.
last_used_preset
–
do not change.
This is set automatically. This allows the board to remember the last used preset before shutting off.
ignition_time
– is the duration in milliseconds of the ignition effect.
retraction_time
– is the duration in milliseconds of the retraction effect.
transition_time
– is the duration in milliseconds of the transition between blade colors.
Presets Section
(
maximum 16 presets)
preset#
– number of preset combination of blade colour number (the first number), blade profile number (second number), and font number (third number).
These presets are selected when the blade is retracted.
3
EDITING PARAMETERS
2
VERSO
INSTRUCTIONS
