KR-sabers VERSO, User Manual

Page: 12 / 30

user manual made by KR-sabers and Dmitry Shtok
| 11 Home
3
stand_by_after
– is a value in seconds of the time to wait without user interaction to enter into stand-by (low power) mode.
mute_mode_after – is a value in milliseconds and represents the time the user has to keep the button pressed to enter and exit the mute mode.
retraction_after – is a value in milliseconds and represents the time the user has to keep the button pressed to produce a retraction.
double_click_time
– is a value in milliseconds and represents the time in which two consecutive button clicks are considered a double click
(for changing the color of the blade).
blaster_after – defines a value in milliseconds and represents the time the user has to keep the button pressed to produce a blaster effect.
master_volume – defines the master output volume. Is a value between 0 and 2.0 (with decimal point), being 1.0 the default volume without any extra gain.
button_blink
– describes the button LED blinking with two values (in milliseconds): the time the LED will stay ON, and the time the LED will stay OFF.
For example, for a sequence of a LED staying ON for 250ms and staying OFF for 750ms, the values will be:
button_blink = 250, 750
The sum of the two values represent the frequency and duty cycle of the blinking sequence (1 second frequency in the above case, with 25% duty cycle).
If you would prefer no blink, configure to 1000,1.
button_count
– the number of buttons installed (1 or 2)
lowbatt_thrs
– indicates the low-battery threshold in millivolts. If the battery voltage is lower than this value for the time defined with
the lowbatt_timebelow parameter, then a low battery condition is declared. If this value is 0, then the low battery detection is disabled.
lowbatt_timebelow – time in seconds with a battery voltage below lowbatt_thrs to declare a low battery condition.
lowbatt_timeabove
– time in seconds with a battery voltage above lowbatt_thrs to exit the low battery condition. This is an optional parameter.
Setting this value to zero will make the low battery condition permanent until the next board reset.
lowbatt_interval – WAV file interval time in seconds. If set to 0, the user indication WAV file is played a single time
(when the low battery condition is detected).
EDITING PARAMETERS
2
VERSO
INSTRUCTIONS
Luxeon Tri-Rebel LED LED 1 LED 2 LED 3
Red/Green/Blue
hbled1 = 0.7, 2.4, 2, 0.35, 2.1 hbled2 = 1, 3.2, 0.4, 0.35, 2.9 hbled3 = 1, 3.05, 0.7, 0.35, 2.8
Red/Green/RoyalBlue
hbled1 = 0.7, 2.4, 2, 0.35, 2.1 hbled2 = 1, 3.2, 0.4, 0.35, 2.9 hbled3 = 1, 3.05, 0.7, 0.35, 2.8
Red/Red/White
hbled1 = 0.7, 2.4, 2, 0.35, 2.1 hbled2 = 0.7, 2.4, 2, 0.35, 2.1 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
Green/Green/White
hbled1 = 1, 3.2, 0.4, 0.35, 2.9 hbled2 = 1, 3.2, 0.4, 0.35, 2.9 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
Blue/Blue/White hbled1 = 1, 3.05, 0.7, 0.35, 2.8 hbled2 = 1, 3.05, 0.7, 0.35, 2.8 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
Amber/Amber/White
hbled1 = 0.7, 3.2, 1, 0.35, 3.0 hbled2 = 0.7, 3.2, 1, 0.35, 3.0 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
DeepRed/DeepRed/White
hbled1 = 0.7, 2.4, 2, 0.35, 2.1 hbled2 = 0.7, 2.4, 2, 0.35, 2.1 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
RedOrange/RedOrange/White hbled1 = 0.7, 2.4, 2, 0.35, 2.1 hbled2 = 0.7, 2.4, 2, 0.35, 2.1 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
Cyan/Cyan/White
hbled1 = 1, 3.2, 0.4, 0.35, 2.9 hbled2 = 1, 3.2, 0.4, 0.35, 2.9 hbled3 = 1, 3.1, 0.5, 0.35, 2.8
Other color combinations also possible, use values from examples above.
Tri-Cree LED LED 1 LED 2 LED 3
Red/Green/Blue
hbled1 = 1, 2.7, 1, 0.35, 2.2 hbled2 = 1, 3.7, 0, 0.35, 3.2 hbled3 = 1, 3.4, 0.33, 0.35, 3.1
Red/Green/RoyalBlue
hbled1 = 1, 2.7, 1, 0.35, 2.2 hbled2 = 1, 3.7, 0, 0.35, 3.2 hbled3 = 1, 3.4, 0.33, 0.35, 3.1
Red/Red/White hbled1 = 1, 2.7, 1, 0.35, 2.2 hbled2 = 1, 2.7, 1, 0.35, 2.2 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
Green/Green/White
hbled1 = 1, 3.7, 0, 0.35, 3.2 hbled2 = 1, 3.7, 0, 0.35, 3.2 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
Blue/Blue/White
hbled3 = 1, 3.4, 0.33, 0.35, 3.1 hbled3 = 1, 3.4, 0.33, 0.35, 3.1 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
Amber/Amber/White hbled1 = 1, 3.3, 0.25, 0.35, 3.05 hbled2 = 1, 3.3, 0.25, 0.35, 3.05 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
DeepRed/DeepRed/White
hbled1 = 1, 2.5, 1.2, 0.35, 2.05 hbled2 = 1, 2.5, 1.2, 0.35, 2.05 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
RedOrange/RedOrange/White
hbled1 = 1, 2.7, 1, 0.35, 2.2 hbled2 = 1, 2.7, 1, 0.35, 2.2 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
Cyan/Cyan/White
hbled3 = 1, 3.4, 0.33, 0.35, 3.1 hbled3 = 1, 3.4, 0.33, 0.35, 3.1 hbled3 = 1, 3.15, 0.5, 0.35, 2.9
Other color combinations also possible, use values from examples above.