SECTION 10
OPERATING INSTRUCTIONS
Setup Komfort 8K1 Control Module–Additional Diagnostic Information
#SFD-36
R.6 February 2022
#SFD-36
R.6 February 2022
47
HUSSONG MFG. CO., INC.
KOZY HEAT FIREPLACES
10.1 Setup Komfort 8K1 Control Module
1. Set the main ON/OFF rocker switch in the OFF position.
2. Remove the remote control components from packaging.
3. Install (3) AAA batteries (included in the components packet) in
the remote control battery bay.
4. Connect the transformer to an AC power supply.
5. Connect the fan to the AUX 300 control module
10.2 Initialize the Komfort
8K1 Control System
1. Verify the ON/OFF/REMOTE switch is in the REMOTE position. A
green LED will illuminate and blink three times.
2. Using a small item, such as a paper clip, press and release the
LEARN button located near the ON/OFF/REMOTE switch.
3. The control module will beep once and illuminate a green LED
for 10 seconds.
4. While the green LED is blinking, press the POWER button on the
remote control. The control module will emit a double beep to
indicate that the remote is initialized to the control system.
10.3 Automatic Safety Turn-off
This system will execute an automatic turn OFF command after 8
hours of continuous main burner operation.
10.4 Backup Battery Operation
This appliance will operate on the backup battery pack in a power
outage. The lifespan of the backup batteries depends on various
factors, such as the quality of the batteries, number of ignitions, etc.
Only install backup batteries in power outages only. Do not leave
batteries installed in the backup battery pack.
10.5 Control System 7 Day Time-out
If your Komfort 8K1 control system is set to pilot-on-demand ignition
with
7
consecutive days without ignition of the main burner, the
pilot will turn off. This is a standard safety feature of the Komfort 8K1
control system.
Once you turn the pilot-on-demand on, the
7
day timer will start. If at
any time during the following
7
days your main burner ignites, it will
reset the timer back to
7
days.
See section
on page 49 for more information about pilot
ignition selection.
How to check if your system is set to pilot-on-demand:
•
The remote control screen will display the snowflake with text
PILOT icon.
To select the preferred pilot ignition:
1. Press the MENU button to activate the menu.
2. Using the UP and DOWN arrows, highlight the PILOT icon and
press SELECT.
3. Use the UP and DOWN arrows to turn the pilot-on-demand ON
or OFF, then press SELECT.
•
A single beep will be emitted from the control module indicating
pilot-on-demand feature has been activated.
•
A double beep will be emitted from the control module
indicating the pilot-on-demand feature has been deactivated.
10.6 Komfort 8K1 Control System
Ignition Sequence
The Komfort 8K1 control module will attempt (1) time for ignition, for
approximately 60 seconds.
If there is no flame ignition (rectification) within the (60) second time
frame, the Komfort 8K1 system will go into a lockout. The control
module will display an error code (see section
), followed by a
blinking red/green LED, indicating a system lockout.
10.6.1 Reset Control Module after Lockout
10.6.1.1 Disconnect Power Supply
•
Disconnect the power supply to the control module. After
approximately (5) second, reconnect power supply.
10.6.1.2 ON/OFF/REMOTE Switch
•
Turn the ON/OFF/REMOTE switch on the control module to OFF.
Wait approximately (5) seconds, and turn the ON/OFF/REMOTE
switch to REMOTE. The control module will illuminate a green
LED (2) times and emit a beep.
•
Turn the ON/OFF/REMOTE switch on the control module to OFF.
Wait approximately (5) seconds, and turn the ON/OFF/REMOTE
switch to ON. The control module will illuminate a green LED (2)
times and emit a beep. The ignition sequence will start again.
10.7 Additional Diagnostic Information
Diagnostic codes are outlined below and should be used as an
additional troubleshooting tool.
Red LED will blink (1) time, then a red/green LED blink (lockout)
•
Error caused by fuel-type selector switch is in incorrect position
or fuel-type selector switch is damaged. Verify selector is in
correct position. If condition persists, replace the control module.
Red LED will blink (2) times, then a red/green LED blink (lockout)
•
Error caused by Insufficient voltage from ignition coil to
pilot flame igniter. Clear the lockout (see section
above) and attempt ignition. If condition persists, replace the
control module.
Red LED will blink (3) times, then a red/green LED blink (lockout
)
•
Error caused by inadequate gas supply. Verify proper inlet
pressure to the gas line.
•
Error caused by detection of false flame or short in sensor lead.
Verify that pilot leads are correctly terminated to the control
module, and that no shorted wires exist.
•
Error caused by sense and/or igniter lead disconnected. Verify
that the pilot sensor rod, igniter rod, and hood are clean.
