background image

Hussong Mfg. Co., Inc. • JOR-30S 

Report No.: 0216GN033S • Rev. 04,

 

October 2016

HUSSONG MANUFACTURING CO., INC.

 

ͷ

Do not store or use gasoline or other 

flammable  vapors  and  liquids  in  the 

vicinity of this or any other appliance.

 

ͷ

WHAT TO DO IF YOU SMELL GAS

• 

Do not try to light any appliance.

• 

Do not touch any electrical switch; do 

not use any phone in your building.

• 

Leave the building immediately.

• 

Immediately call your gas supplier from 

a neighbor’s phone. Follow the gas 

supplier’s instructions.

• 

If you cannot reach your gas supplier, 

call the fire department.

 

ͷ

Installation and service must be performed 

by a qualified installer, service agency or 

the gas supplier. 

    WARNING:

FIRE OR EXPLOSION HAZARD

Failure  to  follow  safety  warnings  exactly 

could  result  in  serious  injury,  death,  or 

property damage.

This  appliance  may  be  installed  in 

an  aftermarket,  permanently  located, 

manufactured  home  (USA  only)  or  mobile 

home, where not prohibited by local codes.
This appliance is only for use with the type 

of  gas  indicated  on  the  rating  plate.  This 

appliance  is  not  convertible  for  use  with 

other gases, unless a certified kit is used.

INSTALLER: Leave this manual with the appliance. 

 

CONSUMER: Retain this manual for future reference.

JORDAN-30S

Model 

#JOR-30S

Direct Vent Gas Fireplace Insert

Tested &

Listed By

OMNI-Test Laboratories, Inc.

C

US

Portland

Oregon USA

Installation and 

Operation Manual

English and French installation manuals are 

available through your local dealer. Visit our website 

 

www.kozyheat.com

 or scan the QR code for our mobile app.

Les manuels d’installation en français et en anglais sont 

disponibles chez votre détaillant local. Visitez 

www.kozyheat.

com ou scannez ce code QR pour notre application mobile.

Summary of Contents for JOR-30S








































Reviews: