41
Platinum Bio
controller service manual - ENGV 04.11
Experts in heating
1.
G
eneral
!
!
1
4.
3
Precau
t
ions
NOTE!!!
Electric shock hazard.
Before installing or removing the device disconnect power
supply in the electrical switchboard.
Before using the appliance, carefully read
all attached instructions.
Keep the service manual and refer to it for any
use of the device in the future.
Follow all warnings and instructions
contained in the service manual.
Make sure that the device is not damaged in any way.
If in doubt, do not use the device and contact the supplier.
In case of any doubts as to safe operation of the device,
you should contact the supplier.
Pay special attention to any warning signs posted
on the housing and packaging of the equipment.
Use the device for its intended purpose.
The device is not a toy, do not allow children to play with it.
Do not allow your children to play with any part
of the packaging of the device.
Prevent an access to small parts such as screws, pins from
children. These elements can be supplied with the equipment
and if swallowed may cause suff ocation of a child.
Do not perform any mechanical or electrical changes
in the device. Such changes may result in improper operation of
the device which does not conform with the standards
and adversely aff ect operation.
Do not put any objects into the device interior through the slots
(eg ventilation), it can cause a short circuit, electric shock, fi re
or damage equipment.
You can not permit for water, moisture and dust penetration
to the device interior, since they can cause a short circuit,
electric shock, fi re or damage equipment.
Ensure proper ventilation of the device, do not cover or block
any ventilation openings and ensure free fl ow of air around it.
The device should be installed inside the premises unless
it is prepared to outdoor operation.
Do not allow the unit to be exposed to shocks and vibrations.
When connecting, make sure that the mains electrical
parameters correspond to the device working range.
To avoid risk of electric shock the device must be connected
to an outlet with the ground terminal. Grounding the outlet must
be done properly by a qualifi ed electrician.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
When connecting, make sure that this will not cause
overloading the electrical circuit. Avoid connecting
the device to the same circuit with motors and other devices
causing pulse-type interferences (e.g., washing machines,
refrigerators, ...)
Before connecting any cables and peripherals to the device,
it is essential to disconnect the power supply.
To completely disconnect the unit from power supply the plug
must be removed from the wall outlet, especially when it will
not be used for a long time.
Protect the power cord from damage; it should be routed
in such a way to not step on it; no objects should be placed
on the cable.
All connections must be made in accordance with the electrical
wiring diagram and with the national or local electrical wiring
codes.
This device does not contain any parts, which the user can
replace itself. All service operations in addition to cleaning,
replacement of the fuse (with the device disconnected from
the mains) and setting the functions should be performed by
authorized service personnel.
Before performing any maintenance, it is essential
to disconnect the unit from the mains.
To clean the device housing do not use gasoline, solvents
or other chemicals that may damage the housing.
It is recommended to use soft cloth.
If the AC power cord is damaged, absolutely do not use such
a device. A damaged cord must be replaced by service
personnel with the new one of the same parameters
as the original cord.
1
4.4
W
as
t
e
e
q
uipmen
t
disposa
l
The electronic device is made of materials, some of which
are suitable for recycling. Therefore, after live expiration
it must be delivered to the point of electrical and electronic
equipment recovery and recycling, or be returned
to the manufacturer. Equipment should not be mixed
with other domestic wastes.
•
•
•
•
•
•
•
•
•
1.
3
Precautions
1.4
W
aste e
q
uipment disposal