NOTE
NOTE
NOTE
NOTE
NOTE
NOTE
NOTE
NOTE
P.S
P.S
●
The speeding alarm setting is changed
from 60 Km/h to 68 Km/h.
Press the
Adjust button
to choose the setting
number.
●
●
Press
Select button
to enters the shift
light setting screen.
●
Bar segment tachometer
●
●
EX. Now the setting is changed from 10,000
RPM to 20,000 RPM.
Press
Select button
to enter sthe speeding
setting screen.
●
●
EX .You want to set the bar segment tachometer
to 20,000 RPM.
Press the
Adjust button
to choose the setting range.
The tachometer range : 10,000,
15,000, 20,000RPM
●
Speed warning light setting
●
●
EX. You want to set the speed warning to 68 Km/h.
Press the
Select button
to move to the digit you
want to set.
Setting range: 30~360km/h (19~225 MPH).
Setting unit: 1 km/h (MPH)
The speed warning light will
light on when the speed
reaches your speed
warning setting.
●
EX. The ignition angle setting is changed
from 1 to 2 (4C-4P).
Press the
Select button
to enter the RPM
setting screen.
●
Function setting instruction
●
Sensor point setting
●
Press the
Select button
to enter the
sensor point setting
●
In main screen
●
In main screen, press and hold the
Select
& Adjust buttons X 3 seconds
to enter the
tire circumference and sensor point setting.
●
Tire circumference setting
●
EX. The tire circumference is 1,300 mm.
●
Press the
Select button
to move to the
digit you want to set.
Setting range: 300~2,500 mm.
Setting unit: 1 mm.
CAUTION!
●
●
Measure the tire circumference (The tire you installed the sensor on) and make sure the number of magnet
sensor point (install the magnet into the disc screw or the sprocket screw.)
The speed displayed on the meter will be affected by the setting, make sure the setting number is correct
before you enter the setting.
130
cm
You could define the valve
as the starting point and the
terminal point to measure
the wheel circumference
with a measuring tape.
●
●
Press the
Adjust button
to choose the
setting number.
EX. The circumference setting is changed
from 1,000 mm to 1,300mm.
●
●
Press the
Adjust button
to choose
the setting number.
EX. The sensor point you want to set is 6.
The sensor point setting range:
6 points.
●
●
EX. the sensor point setting is changed
from 1 P to 6 P.
Press the
Select button
to enter the
RPM pulse setting.
●
RPM pulse setting
The piston type can be set is
0.5, 1, 1.5, 2, 2.5, 3, 4, 5, 6.
The corresponding
stroke and pistons number.
The corresponding RPM signal
number per ignition.
The setting
value
2 RPM signals per 1 ignition.
2 RPM signals per 3 ignitions.
2 RPM signals per 5 ignitions.
2 RPM signals per 10 ignitions.
1 RPM signal per 1 ignition.
1 RPM signal per 2 ignitions.
1 RPM signal per 3 ignitions.
1 RPM signal per 4 ignitions.
1 RPM signal per 6 ignitions.
0.5
1
1.5
2
3
2.5
4
5
6
2C-1P
2C-2P
2C-3P
2C-4P
2C-6P
4C-1P
4C-4P
4C-6P
4C-5P
4C-8P
4C-10P
4C-12P
4C-2P
4C-3P
CAUTION!
EX. You want to change the current setting
value from 1 to 2.
●
●
●
Press the Adjust button to enter the
corresponding value for the RPM signal
number per ignition.
(Check the reference table below!)
EX. The original setting is 0.5 (4C-1P).
4-2
●
EX. Change the setting to Lo. (The negative
impulse)
Press the
Adjust button
to choose the input
signal you want to set.
●
●
●
EX. Change setting to Hi (The positive
impulse)
Press the
Select button
to enter the RPM
setting screen.
●
The negative impulse
If the tachometer can't detect the
signal (No RPM is displayed on the
screen), choose another setting,
and check it again.
The impulse setting range is between
Hi (the positive impulse)& Lo (the
negative impulse)
Wh022ba04d-
3
Most of the 4-cycle bikes with one single piston are igniting
every 360 degree once, so the setting should be the same as the bike with 2-cycle
and one piston engine.
