Korg TRITON Extreme, Manual

Page: 110 / 354

99
Sequencer
P0
P1
P2
P3
P4
P5
P6
P7
P8
P9
9–5: VALVE FORCE
Here you can adjust the settings of the Valve Force analog
vacuum tube circuit.
Valve Force can be applied to specific tracks, either alone or
together with an insert effect, or it can be applied at the final
output stage to add a subtle boost or the distinctive tonal
character that is unique to vacuum tubes.
Use the VALVE FORCE [ON/OFF] key to turn Valve
Force on/off.
Valve Force is a stereo-in/stereo-out analog circuit.
Valve Force parameter settings are saved indepen-
dently for each song.
9–5a: VALVE FORCE
Input Trim [000...127]
Ultra Boost [000...127]
Tube Gain [000...127]
Output Level [000...127]
These parameters set the input to Valve Force, the amount of
ultra-low-frequency boost, the input gain to the vacuum
tube, and the output level from Valve Force.
For details on these parameters, refer to Program mode.
As in Program mode, you can use MIDI NRPN control
change messages to control the VALVE FORCE [ON/
OFF] key and the parameters (knobs) listed above.
However, the MIDI channel used for control will be the
“Ctrl Ch”. In order to record and play back operations
of these parameters, the MIDI channel of the recording
track and the “Ctrl Ch” must be the same.
Placement [Final, Insert (User 3/4 BUS)]
Specifies the location of the Valve Force circuit.
For details on this parameter, refer to Program mode.
Valve Force cannot be applied to resampling that uses
the S/P DIF output or L/R as the Source BUS, since
these signals are being processed in digital form.
Here’s an example of settings when you’ve set “Placement”
to Insert (Use 3/4 BUS) in Sequencer mode.
Example settings)
Set “BUS Select” (8–1(2)b) or post-IFX “BUS Sel.” (8–3a) to
insert Valve Force at the desired location. Use Valve Force
“BUS Sel.” (9–5a) to specify the output destination from
Valve Force.
• Track
→
Valve Force
→
audio output
“BUS Select”: 3/4(Tube)
Valve Force “BUS Sel.”: L/R or 1/2
You can send more than one track to Valve Force. How-
ever you can’t make Valve Force settings independently
for each track.
• Track
→
Valve Force
→
insert effect
→
master effects
→
audio output
“BUS Select”: 3/4(Tube)
Valve Force “BUS Sel.”: IFX1...5
Post-IFX “Send1,” “Send2”: as desired
Post-IFX “BUS Sel.”: L/R or 1/2
Don’t set the post-IFX “BUS Sel.” to 3/4(Tube), since
doing will cause a feedback loop that may produce
unpleasant distortion.
• Track
→
insert effect
→
Valve Force
→
master effects
→
audio output
“BUS Select”: IFX1...5
Post-IFX “BUS Sel.”: 3/4(Tube)
Valve Force “BUS Sel.”: L/R or 1/2
Valve Force “Send1,” “Send2”: as desired
• Track
→
insert effect
→
Valve Force
→
insert effect
→
master effects
→
audio output
“BUS Select”: IFX1...5
Post-IFX “BUS Sel.”: 3/4(Tube)
Valve Force “BUS Sel.”: IFX1...5
Post-IFX “Send1,” “Send2”: as desired
Post-IFX “BUS Sel.”: L/R or 1/2
Don’t set the post-IFX “BUS Sel.” to any preceding IFX,
since doing so will cause a feedback loop that may pro-
duce unpleasant distortion.
In the same way, you can apply Valve Force to the
Audio Input, and use it for In-Track Sampling.
Ctrl Ch (Control Channel) [Ch01...16, Gch]
Specifies the MIDI channel on which Valve Force will be
controlled.
Gch:
Control using the global MIDI channel specified by
“MIDI Channel” (Global P1).
9–5b: Post VALVE FORCE Mixer
Pan(CC#8) [L000...C064...R127]
BUS Sel. [L/R, IFX1...5, 1, 2, 1/2, Off]
Send1 [000...127]
Send2 [000...127]
ADC OVERLOAD !!
These parameters specify the destination to which the Valve
Force output is sent.
Refer to Program mode for details on these parameters.
As in Program mode, you can use CC#8 to control “Pan
(CC#8),” CC#93 to control “Send1,” and CC#93 to con-
trol “Send2.” However, the MIDI channel used for con-
trol will be the “Ctrl Ch”.
“Pan,” “BUS Sel.”, “Send1,” “Send2,” and “ADC
OVERLOAD !!” apply only if “Placement” is set to
Insert (Use 3/4 BUS).
9–5
9–5a
9–5b