Korenix JetNet 7852G-4XG Series User Manual Download Page 933 | Manualshive

Page: 933 / 1568

background image

Korenix Technology Co., Ltd.

Industrial

Layer 3 Managed Ethernet Switch

_____________________________________________________________________________

Industrial Layer 3 Managed Ethernet SwitchUser Manual

Page: 933/1568

9

IPv6 Commands

9.1

Tunnel Interface Commands

The commands in this section describe how to create, delete, and manage tunnel interfaces.Several
different types of tunnels provide functionality to facilitate the transition of IPv4 networks to IPv6 networks.
These tunnels are divided into two classes: configured and automatic. The distinction is that configured
tunnels are explicitly configured with a destination or endpoint of the tunnel. Automatic tunnels, in contrast,
infer the endpoint of the tunnel from the destination address of packets routed into the tunnel. To assign
an IP address to the tunnel interface, please refer to

“ip address” command. To assign an IPv6 address

to the tunnel interface, please refer to

“ipv6 address” command.

9.1.1

Show Commands

9.1.1.1

show interface tunnel

This command displays the parameters related to tunnel such as tunnel mode, tunnel source address
and tunnel destination address.

Syntax

show interface tunnel [<0-7>]

Default Setting

None

Command Mode

Privileged Exec

Display Message

If you do not specify a tunnel ID, the command shows the following information for each configured
tunnel:

Tunnel ID:

Shows the tunnel identification number.

Interface:

Shows the name of the tunnel interface.

Tunnel Mode:

Shows the tunnel mode.

Source Address:

Shows the source transport address of the tunnel.

Destination Address:

Shows the destination transport address of the tunnel.

If you specify a tunnel ID, the command shows the following information for the tunnel:

Interface Link Status:

Shows whether the link is up or down.

«
...
931
932
933
934
935
...
»

Summary of Contents for JetNet 7852G-4XG Series

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for JetNet 7852G-4XG Series

Brand: Paradyne Pages: 2

3C410012A - OfficeConnect Remote 531 Access...

Brand: 3Com Pages: 72

Brand: WaiLan Pages: 27

Brand: EMCIS Pages: 14

Brand: Patton electronics Pages: 2

Brand: Lanner Pages: 78

Brand: Baicells Pages: 10

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

COMMWARE ECHO 5G

Brand: pivotal Pages: 2

Brand: Patton Pages: 62

Brand: OneAccess Pages: 47

Brand: Planet Pages: 2

Brand: Cradlepoint Pages: 2

Brand: Lanner Pages: 141

Brand: ExtraHop Pages: 3

Brand: Omron Pages: 4

Brand: ZyXEL Communications Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands