background image

VII. Maintenance

With Kooltronic Air-Cooled Heat Exchangers the use of a filter is optional. If you do choose to use a filter, and
wish to remove it for cleaning or repair, follow the instructions below.

7

Optional Filter Removal and Service

Kooltronic Heat Exchangers feature an easily removable optional inlet filter.

1.

Move the filter up and toward you from the Filter Retainer.

2.

After removal, the filter should be flushed under warm running water 
with the clean side up, driving contaminants out the dirty side of the 
filter. If the accumulated dirt is oily, washing in a detergent bath is 
recommended, followed by warm water rinse as above.

3.

The filter may be sprayed with 

Kooltronic A-16 Filter Recoating 

Adhesive

to trap fine airborne contaminants, or they can simply 

be dried and reinstalled as strainer type filters. 

Recoating is recommended for the best results.

4.

Reinstall the filter in the Filter Retainer. 

VIII. Packing Procedure

Keep Heat Exchanger in proper upright position.

Pack Heat Exchanger in an appropriate carton (preferably original carton if possible), with adequate internal
protective packaging, making sure carton is marked properly.

For local controlled transportation, strap carton to a secure part of the vehicle to prevent falling or sliding,
and to minimize vibration, etc.

For common carrier shipment, band unit(s) securely to a pallet. Unpalletized shipment risks severe
damage which voids the warranty.

CAUTION

Disconnect electric power from the Heat Exchanger

before proceeding.

Summary of Contents for KXRP28









Reviews: