background image

6

VII. Maintenance

Kooltronic Air-Cooled Heat Exchangers are designed to require only routine cleaning
of air filters and the heat exchanger element to assure unimpeded airflow through the
heat exchanger element. It is not possible to recommend specific filter cleaning inter-
vals since the level and the nature of air borne particulate matter differs widely with
each installation. It is generally sufficient to remove and wash the reusable alu-
minum mesh air filter when the outer surface of these filters appear covered with a thin
layer of dust or lint.  Filter recoating adhesive is recommended. Appropriate dis-
posable filters are available from Kooltronic.
If filter service is neglected or delayed, the heat exchanger will not perform at its design
capacity. The first indication of excessively clogged air filter is usually a gradual
increase of temperature within the equipment cabinet.  Continued operation under
these conditions will cause damage, shorten blower motor life and void the warranty.

1

1/

2

5

3/

16 

TYP.

POWER
CORD

FILTER

M/TAB

18

K

17

1/

16

WARM AIR RETURN
FROM ENCLOSURE

WARM AMBIENT
AIR OUTLETS

COOL AIR OUTLET
TO ENCLOSURE

WARM AIR RETURN
FROM ENCLOSURE

FILTERED AMBIENT
AIR INLET

COOL AIR OUTLET
TO ENCLOSURE

A

18

9/

16

18

9/

16

4 TYP.

1

1/

4

UNIT
OUTLINE

(J)

.250 DIA.

HOLES

A

B

G TYP.

1

1/

2

15

TYP.

(H)

.312 DIA.

HOLES

E

F

M/TAB
OUTLINE

C

D TYP.

9

7/

8

12

13/

16

12

1/

8

3

3/

16

2

7/

8

9

3/

4

1

3/

4

5

9/

16

17

3/

4

11/

16

3/

8

Dimensions (inches) are for reference only and are subject to change.

Figure 1

Drawings and Dimensions

UNIT MUST BE 12” MINIMUM ABOVE
FLOOR FOR FILTER ACCESS

MOUNTING PLAN

UNIT

M/TAB & CUTOUTS

DIMENSIONS 

(inches)

Model

A

B

C

D

E

F

G

H

J

K

Series 38

37

3/

4

36

11/

16

12

3/

4

12

3/

4

18

1/

8

2

1/

2

4

11/

32

6

27

37

Series 47

47

45

15/

16

12

1/

4

11

1/

4

27

3/

8

2

1/

2

4

8

33

46

1/

4

Series 59

59

58

16

1/

4

15

1/

4

38

1/

2

3

3/

8

4

8

39

58

1/

4

Summary of Contents for KNHX38 Series









Reviews: