background image

VII. Specific Model Data

Mounting

The Kooltronic Special Purpose Air Conditioners K   AC4P3777R have been engineered to be installed easily. To
avoid damaging your air conditioner, please read the following information before installation:

1.

After pre-installation testing disconnect both the power cord and the remote control. 

2.

Apply supplied gaskets to the unit front panel. (See Gasket Installation)

3.

Remove two 1/4" nuts from the upper studs and save them.

4.

Hang the unit on the enclosure on the two upper studs. Run the unit power cord through the enclosure
cutout.

5.

Secure the unit to the enclosure using the remaining (4) supplied 1/4" bolts and nuts, the two saved 1/4"
nuts, and the supplied (7) washers (two washers must be used on upper left mounting hole - See Mounting
Plan) and (6) lock washers.

6.

Attach the plastic drain hose to the drain tubing on the bottom of the air conditioner using the supplied
clamp.

7.

Install the remote control inside of the enclosure.

8.

Plug the remote control 3 position connector into the unit receptacle labeled “Control.” Plug the remote
control power cord into the unit receptacle labeled “Thermostat Power.”

9.

Plug the unit power cord into the enclosure outlet.

7

Summary of Contents for KAC4P3777R


















Reviews: