01 - AC Adapter Input
02 - Air Compress
or
Vacuum Switch
03 - Light Switch
04 - Bulb Housing Lock
05 - Power Input Indicator Light
06 - Voltage Switch
07 - DC Power Switch
08 - 12V/Power Socket
09 - Air Pressure Gauge
10 - Handle
11 - Vacuum Nozzle Release Switch
12 - Vacuum Nozzle
13 - Air Compressor Hose Connection
14 - Main Housing
1
PARTS IDENTIFICATION:
15 - Clear Lens Cover
16 - Power Indicator Light
17 - Red Light Lens
18 - Accessory Storage Tray
19 - Accessory Story Tray
Release Button
Air Compressor
OFF
Vacuum
OFF
Emergency
Blinker
Flashlight
Button
DIRECTIONS FOR USE
VACUUMING:
Plug one end of the 12V connector Cord (22) into the 12V Power Socket
(08) on the AutoGuard. Plug the other end into the 12V socket in the vehi-
cle. Push the Vacuum Control Switch (02) to the vacuum position (02B)
for operation. Connect the crevice tool (21) to get to hard to reach spaces.
CLEANING VACUUM FILTER:
For proper operation, clean the Vacuum Filter (28) after each use. Remove
the Vacuum Nozzle (12) by pressing down on the Vacuum Nozzle Release
Switch (11) with one hand and pulling on the nozzle with the other hand.
Lift the filter out of the nozzle and remove any dust or debris. Reinstall the
filter into the vacuum nozzle and snap the
nozzle back into the main housing of the
AutoGuard.
NOTE:
Do not operate the vacuum function when
recharging by the AC adapter.
ACCESSORIES:
Crevice Tool
12V Connector Cord
(built in 10A fuse)
Air Pumping
Hose
Accessory Adapter Cord
DC Power Plug
Multi-headed
Connector
AC Power Adapter
Nozzle
21
22
23
24
25
26
20
28
INFLATING A TIRE:
Plug one end of the 12V Connector Cord (22) into the 12V Power Socket
(08) on the AutoGuard, then plug the other end into the 12V socket in the
vehicle. Attach one end of the Air Pumping Hose (23) to the Air
Compressor Hose Connection (13) on the AutoGuard. Attach the other end
to the air valve on the tire you wish to inflate. Push the Air Compressor
Control Switch (02A) to the Air Compressor position. Watch the Air
pressure Gauge (09) and turn the Air Compress Switch (02A) to “OFF”
when the desired air pressure is reached.
BE SURE NOT TO OVER-
INFLATE.
In some vehicles, the ignition switch has to be in the “ON” posi-
tion to apply power to the 12V socket.
NOTE:
1. The AutoGuard can be used to inflate other items such as a bicycle, ath-
letic ball, inflatable mattress, etc.
2. Do not inflate while recharging by the AC adapter.
3. Continuous pumping should never exceed 10 minutes 10 minute inter-
vals should be applied.
POWER BANK:
Push the Voltage Switch (06) to the appropriate voltage needed such as a
6V. For example, the Power Indicator Light (16) will turn RED, indicating
the power is being output. Plug the single end of the DC Power Plug (25)
into the DC power output and choose one of the multi-headed plugs that’s
fitted to the electronic device you wish to use and plug it in. THE
AUTOGUARD CAN BE USED TO POWER ELECTRONIC DEVICES THAT ARE
POWERED UNDER THE VOLTAGE OF 3/6/9V, SUCH AS MOBILE PHONES
AND AUDIO/VISUAL ELECTRONICS.
NOTE:
This function is designed to be used for EMERGENCY only.For regular
power supply, the use of a standard power recharger is recommended.
2
