Kontron COMe-mCT10 User Manual Download Page 21

Page: 21 / 92

3.7

Standards and Certifications

RoHS

The

COMe-mCT10

is compliant to the directive 2002/95/EC on the restriction of the use of certain hazardous substances

(RoHS) in electrical and electronic equipment.

CE marking

The

COMe-mCT10

is CE marked according to Low Voltage Directive 2006/95/EC – Test standard EN60950

Component Recognition UL 60950-1

The

COM Express® mini

form factor Computer-on-Modules are Recognized by Underwriters Laboratories Inc.

Representative samples of this component have been evaluated by UL and meet applicable UL requirements.

UL Listings:

NWGQ2.E304278

NWGQ8.E304278

WEEE Directive

WEEE Directive 2002/96/EC is not applicable for Computer-on-Modules.

Conformal Coating

Conformal Coating is available for Kontron Computer-on-Modules and for validated SO-DIMM memory modules. Please
contact your local sales or support for further details.

Summary of Contents for COMe-mCT10





























































































Search results

Summary of Contents for COMe-mCT10

Reviews:

Related manuals for COMe-mCT10

Brands by name

Popular brands

Kontron COMe-mCT10, User Manual

Search results

Summary of Contents for COMe-mCT10

Reviews:

Related manuals for COMe-mCT10

Brands by name

Popular brands