background image

INTRODUCTION

SAFETY INFORMATION

1

Thank you for your purchase of 

Könner & Söhnen

 products. This manual contains a brief description of 

safety, use and debugging. More information can be found on the official manufacturer’s website in the 

support section: 

ks-power.de/betriebsanleitungen

.

You can also go to the support section and download the full version of the manual by scanning the QR 

code, or on the website of the official importer of Könner & Söhnen products:

 www.ks-power.de/en

The manufacturer reserves the right to make changes to the generators, which may not be reflected in this 

manual. Pictures and photos of the product may vary from its actual appearance. At the end of this manual, 

you will find contact information which you are free to use in case of any issues.
All data specified in this owner’s manual are the most up to date at the time of its publication. The current 

list of service centers can be found on the website of the official importer: 

www.ks-power.de/en

We care about the environment, therefore, we consider it expedient to save

We care about the environment, therefore, we consider it expedient to save

paper and leave in print a short description of the most important sections.

paper and leave in print a short description of the most important sections.

Be sure to read the full version of the manual before

getting started!

Failure to follow the instructions marked with this sign 

may lead to serious injury or death of the operator or 

third parties.

Useful information on operation of the machine.

ATTENTION – DANGER!

IMPORTANT!

Please, read this manual carefully before use!

WARNING!

PROTECTING YOURSELF AND THOSE AROUND YOU

1.1

This is a high-powered machine, with moving parts 

operating with high energy. You must operate the 

machine safely. Unsafe operation can create a number 

of hazards for you, as well as anyone else in the nearby 

area.

WARNING!

Safety symbols and description of inscriptions can be found in the full web version.

Safety symbols and description of inscriptions can be found in the full web version.

Always take the following precautions when using 

this machine:
• Always wear protective goggles or safety glasses 

with side shields while using the log splitter to 

protect your eyes from possible thrown debris.
• Avoid wearing loose clothing or jewelry, which 

can catch on moving parts.
• We recommend wearing gloves while using the 

log splitter. 
• Wear shoes with non-slip treads when using your 

log splitter. Do not use the machine while barefoot 

or wearing open toed sandals.
•Wear long pants while operating the log splitter.
• Keep bystanders at least 50 feet away from 

your work area at all times. Stop the motor when 

another person or pet approaches.
• Never allow children to operate the log splitter.
• Keep in mind that the operator or user is 

responsible for accidents or hazards occurring to 

other people, their property, and themselves.

www.ks-power.de/en

   

|

    1

Summary of Contents for KS 15TKG 52/35


















Reviews: