15
7)
As soon as the equipment responds, press the OK button (
ok
) to con
fi
rm the programming and hold it until
the signal LED (
)
fl
ashes twice.
8)
Test the functionality of your remote control using the standby button ( ) and then with the buttons 1 to 47
(according to the function description table).
9)
If the equipment responds properly to all functions, your KN-URC80B is correctly programmed and can be
used.
Note
:
It could happen, that during the search process, the KN-URC80B
fi
nds several codes to which your TV set
responds, but where all buttons do not function for each code. In this case, the search process should be
re-started (steps 3 to 9) until you obtain the best code. Re-starting the search process starts at the last saved
programming.
Automatic search feature
Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your
equipment cannot be found, you may use the automatic search feature.
1)
Switch on your TV, satellite receiver or your DVB-T / cable box (STB), your DVD / Bluray player or recorder
(DVD) and your audio equipment.
2)
Press and hold the TV (
tv
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button depending on the level that you wish to
programme until the signal LED (
)
fl
ashes twice.
Note
:
For audio equipment,
fi
rst press the Shift button (
shift
) and then the
TV/CD button (
tv
/
cd
) for CD,
STB/TAPE button (
stb
/
tape
) for TAPE,
DVD/TUNER button (
dvd
/
tuner
) for TUNER or
AUX/AMP button (
aux
/
amp
) for AMP
3)
Using the numeric buttons, enter
the code
1 0 0 1
for TV,
the code
3 0 0 1
for STB,
the code
5 0 0 1
for DVD,
the code
6 0 0 1
for CD,
the code
7 0 0 1
for TAPE,
the code
8 0 0 1
for TUNER or
the code
9 0 0 1
for AMP.
The signal LED (
)
fl
ashes twice in order to con
fi
rm that the search mode has been activated.
4)
For TV, STB and AMP, hold the standby button ( ); for DVD, CD and TAPE, hold the stop button ( ) or for the
TUNER, hold button 2 (
2
) of your KN-URC80B pressed until the equipment switches off; for DVD, CD or
TAPE until playback stops or with the TUNER, until it switches to the next programme. This step may take
several minutes.
5)
As soon as the equipment responds, press the OK button (
ok
) to con
fi
rm the programming and hold it until
the signal LED (
)
fl
ashes twice.
6)
Test the functionality of your remote control using the standby button ( ) and then with the buttons 1 to 47
(according to the function description table).
7)
If the equipment responds properly to all functions, your KN-URC80B is correctly programmed and can be
used.
Note
:
It could happen, that during the search process, the KN-URC80B
fi
nds several codes to which your TV set
responds, but where all buttons do not function for each code. In this case, the search process should be
re-started (steps 2 to 7) until you obtain the best code. Re-starting the search process starts at the last saved
programming.
Code reader
The code reader can be used to display the codes that you have found in the search process so that you can
make a note of them:
1)
Press and hold the TV (
tv
), STB (
stb
), DVD (
dvd
) or AUX (
aux
) button depending on the level that you wish to
programme until the signal LED (
)
fl
ashes twice.
BA König KN-URC80B, 135x215 mm CS6.indd 15
BA König KN-URC80B, 135x215 mm CS6.indd 15
12.09.2012 10:56:07
12.09.2012 10:56:07
