21472 Speaker stand XL
INTENDED USE:
- Large, up to 2.5 m high stand with a manually adjustable extension for
-
speakers with 35 mm inner flange bushing
FEATURES & CAPABILITIES
- Permanent high stability and steadiness thanks to the generously
-
dimensioned aluminium tubes (ø 35/42 mm)
- Equipped with integrated shock absorber, speaker fitting aid, patented
-
push-button system for height adjustment etc.
- Suitable for rehearsal rooms, studios, stages and on tour,
-
space-saving folding and low net weight
- Maximum design load: 50 kg*
- Height 1580 - 2474 mm, base circle ø 1558 mm, weight 4.1 kg
SAFETY INSTRUCTIONS (summary)
Please see the attached sheet for precise details.
A. GENERAL
- The maximum centric load capacity adds up to 50 kg*
- Ensure that the floor is suitable, i.e. level and loadbearing
- Works should be carried out by competent staff (technical and physical)
B. NOTE concerning "PREDICTABLE MISUSE"
- Base and extension tube combination must always be installed vertically
- Do not load the stand only on one side
- It is not allowed to shift the stand, especially under load
- For indoor use only
C. BEFORE USE
- Undergo a visual inspection - do not use damaged stands
D. ASSEMBLING THE STAND
- For maximum stability, set the largest possible root diameter
- Tighten the clamping screws firmly, but without using any tools. Manual force is quite sufficient
- The locking pin
10
must remain engaged - except when adjusting the height
E. DURING USE
- Safety during operation is based on:
1. OBSERVANCE of this instruction manual, especially the points mentioned under A-F
2. CORRECT OPERATION
2.
a. Always carry out works on the stand with two suitable persons
2.
b. Never unscrew the locking bolt
8
or clamping screw
7
of the extension tube in an
2. b.
uncontrolled manner
3. CONTROL of LATERAL FORCES (relevant due to danger of tipping)
3.
Lateral forces must be avoided. These occur when:
3.
a. the stand is inclined
3.
b. the load balance is exocentric
3.
c. external shocks such as kicks, pulling on the stand, vibrations, wind, etc. are suffered)
F. AFTER USE
- Allow the load to draw in slowly and in a controlled manner with the aid of two suitable persons.
INSTALLATION - / USER INSTRUCTIONS
COMPONENTS
After unpacking, visually inspect whether all parts are present and - if identifiable - whether they
are in order:
a
Stand, folded,
b
Clamping screw (M8 x 23 mm) for triangular clamp
c
Clamping handle (M8 internal thread) of the telescopic bolt clamp
d
Instruction manual
ASSEMBLY, DIMENSIONS
The 21472 stand is completely pre-assembled ex factory. For installation proceed as follows:
1
Loosen slightly the clamping screw
b
of the triangular clamp.
2
Preferably, pull the legs apart simultaneously until...
3
...the connecting struts are horizontal (= maximum root diameter)
4
Tighten clamping screw
b
again – manual force is sufficient.
4
NOTE: Avoid overtightening - it strains the components.
TECHNICAL DATA
Thank you for choosing this product. Please read and follow carefully the instructions. They
inform you about all important steps, that are required for a safe assembly and operation.
Please keep the instructions for future reference.
KÖNIG & MEYER
GmbH & Co. KG
Kiesweg 2, 97877 Wertheim, www.k-m.de
21472-000-55 Rev.01. 4/20
Material
Base and stand tubes: aluminium, black
Extension tube: steel, powdered, black
Struts, screws, rivets: steel
Clamps, handles, attachment aid: PA
Parquet protectors, dampener: TPE
Dimen-
sions
Max. base circle: ø 1558 mm
Height: min.1580 - max. 2474 mm
Packing size: 1302 x 138 x 120 mm
Net weight: 4.1 kg
Load
max. 50 kg*
Pull-out
ø 35 x 894 mm / mounting aid
Box
1300 x 140 x 140 mm
Accessories
(optional)
Carrying case 21319
(for one 21471)
Flange adapter (19654, 19656)
Mounting adapter (19580, 24281)
Warning strip 21402
Leveling leg 21445
* With centric loading, on a horizontal surface and without lateral forces
* (wind, shocks etc.)
ASSEMBLY, DIMENSIONS
Top view
Depth of
the K&M
flange
adapter
19656
Root circle diameter 1238
T
ipping line
Centre
COMPONENTS
