background image

E-1

JS-506 

Job Separator

INSTALLATION MANUAL

A2YV-9551-00

Applied Machines: C554e/C454e/C364e/C284e/C224e/C554/C454/C364/C284/C224/C368/C308/554e/454e/364e/

284e/224e/367/287/227

COLOR MFP: 55 ppm/45 ppm/36 ppm/30 ppm/28 ppm/22 ppm

MFP: 55 ppm/45 ppm/36 ppm/28 ppm/22 ppm

Product Code: A5AY/A5C0/A5C1/A5C2/A5C4/A2XK/A4FJ/A161/A4FK/A4FM/A7PU/A7PY/A61D/A61E/A61F/A61G/

A61H/A789/A7AH/A7AK

1. Accessory parts

*1

This part is used only when the Job Separator 
is installed to 367/287/227.

*2

This part is used only when the Job Separator 
is installed to C554e/C454e/C364e/C284e/
C224e/C554/C454/C364/C284/C224/C368/
C308/554e/454e/364e/284e/224e.

Note:

    • This manual provides the illustrations of the 

accessory parts and machine that may be 
slightly different in shape from yours. In that 
case, instead of the illustrations, use the 
appearance of your machine to follow the 
installation procedure. This does not cause any 
significant change or problem with the proce-
dure.

    • If none of the later steps instruct you to use the 

parts including screw and cover that you 
removed following the instructions described in 
this manual, discard them.

No.

Name

Shape

Q’ty

1. Upper tray

1

2. Sensor unit

1

3. Film

1

4. Hook

*1

1

5. Regulating

plate

*1

1

6. Screw A 

(3 x 8 mm)

1

7. Screw B 

(3 x 10 mm)

3

8. Screw C 

(3 x 16 mm)

*2

2

9. Screw D 

(4 x 8 mm)

*1

1

10. Installation 

manual

1 set

Keep this bag away from babies and 
children. Do not use in cribs, beds, 
carriages, or playpens.

The thin film may cling to nose and 
mouth and prevent breathing. This bag is 
not a toy.

Summary of Contents for JS-506












Reviews: