manualshive.com logo in svg

Kongsberg Simrad MF90, Installation Manual

Share
Download
Kongsberg Simrad MF90 Installation Manual Download Page 191

476671/B

189

Inspecting the installation of the MF90 system

Topics

Visual inspection of the display, page 189

Visual inspection of the Processor Unit, page 191

Visual inspection of the Operating Panel, page 193

Visual inspection of the Transceiver Unit, page 194

Visual inspection of the hull unit, page 196

Checking the environmental conditions in the sonar room, page 198

Making sure that all MF90 system cables are properly connected, page 199

Visual inspection of the display

A visual inspection of the display is required to verify that the unit has not been physically
damaged during the installation.

Prerequisites

The MF90 system hardware units are installed as specified in this manual. The MF90 system
is turned off. You need the following equipment:

• Multimeter

Context

This test procedure is only applicable when the display is provided by Kongsberg Maritime
as a part of the MF90 delivery.

Procedure

1

Make sure that the display is installed in the correct location, and that it is suitably
orientated with respect to ambient light conditions and reflections.

2

Make sure that the physical installation of the unit has been completed.

a

Make sure that the structure to which the display is fastened is substantial enough
to hold the unit securely under all operating conditions.

b

Make sure that ample space is provided around the unit to allow for maintenance
and replacement of parts.

Setting to work

Summary of Contents for Simrad MF90











































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands