Kone V3F18, Installation Instruction

Page: 21 / 42

V3F25/18 drive V3F25/18 drive
Installation Instruction Installation Instruction
© © 2004 KONE Co 2004 KONE Corporation rporation
AM-11.65.020 AM-11.65.020
A Alll l rriig gh htts s rre es se errv ve ed d.. 2 21 1 ((4 42 2)) ((E E) ) 2 20 00 04 4--0 01 1--0 08 8
5 5 C CO OM MM MIIS SS SIIO ON NIIN NG G O OF F T TH HE E M MA AC CH HIIN NE E A AF FT TE ER R R RO OP PIIN NG G
Refer to the elevator level installation manual before commissioning with ropes. Refer to the elevator level installation manual before commissioning with ropes.
5 5..1 1 L LW WD D s se ettu up p
Normal drive including relevelling are not permitted until LWD setup is done. RDF (machine Normal drive including relevelling are not permitted until LWD setup is done. RDF (machine
room inspection drive in North America) and setup drive are
room inspection drive in North America) and setup drive are permitted. permitted.
5. 5.1. 1.1 1 Ch Chec ecki kin ng t g the he L LWD WD o ope pera rattio ion n
MiniSpace™, MonoSpace® Special and elevators in North America (EcoSystem MR® MiniSpace™, MonoSpace® Special and elevators in North America (EcoSystem MR®
and MonoSpace®):
and MonoSpace®):
MonoSpace® and TranSys™ elevators with V MonoSpace® and TranSys™ elevators with V
3 3
F18 drive: F18 drive:
Do this check only if there are problems. Do this check only if there are problems.
S Stte ep p A Ac cttiio on n N No otte e
1 1 T Tur urn t n the he el elev evat ator or to to RD RDF ( F (ma mach chin ine r e roo oom i m ins nspe pect ctio ion d n dri rive ve in in No Nort rth A h Ame meri rica ca). ).
2 2 En Ensu sure re th that at th the c e ca ar i r is e s emp mpty ty. D . Dri rive ve th the c e car ar to to s sui uita tabl ble f e flo loor or le leve vel. l.
3 3 Ch Chec eck k th the e me mech chan anic ical al a adj djus ustm tmen ent t of of L LWD WD un unde der r th the e ca carr..
4 4 Ch Chec eck t k tha hat v t vol olta tage ge be betw twee een p n poi oint nts L s LWD WD - A - AGN GND o D on H n HCB CB bo boar ard i d is b s bet etwe ween en 0. 0.5 V 5 V
and 1.5 V. If not, check the air gap. It should be 3 - 5 mm. and 1.5 V. If not, check the air gap. It should be 3 - 5 mm.
S Stte ep p A Ac cttiio on n N No otte e
1 1 T Tu urrn n tth he e e elle ev va atto or r tto o R RD DF F..
2 2 En Ensu sure re th that at th the c e ca ar i r is e s emp mpty ty. D . Dri rive ve th the c e car ar to to s sui uita tabl ble f e flo loor or le leve vel. l.
3 3 Ad Add a d and nd re remo move ve so some me lo load ad in in ca car a r and nd se see t e tha hat th t the v e vol olta tage ge be betw twee een p n poi oint nts L s LWD WD
and AGND on the HCB board is changing when changing the load in car. and AGND on the HCB board is changing when changing the load in car.
If the voltage does not change, check connections and mechanical condition of
If the voltage does not change, check connections and mechanical condition of
LWD. You may have to replace LWD and its hanger.
LWD. You may have to replace LWD and its hanger.