background image

W

A

R

N

I

N

G

W

A

R

N

I

N

G

If pressurized air or water is used make sure appropriate protective articles are used.
Do not use flammable liquids to clean spreader.

L

u

b

r

i

c

a

t

i

o

n

L

u

b

r

i

c

a

t

i

o

n

Before using the spreader for the first time, put 25 shots or until grease flows out of hub (with a hand 
grease gun) in zerks on spreader transmission and wheel hubs. After every 8 hours of use put in (3 
to 4 shots with a hand grease gun). Make sure the grease zerks are clean from dirt and other 
foreign materials before injecting the grease. 

NOTE: Use only a grade Type II or Lithium tube 

grease. 

Spreader should be stored ready to use next time needed. Do not store spreader with damaged or 
missing parts as failure to fix can be forgotten and further damage or hazards may be encountered 
during next use.
Store the spreader in a dry area protected from the elements.
Do not store with fertilizer in hopper or any other material as these are typically corrosive and can 
damage the hopper over time. Also the material can solidify and be difficult to remove or even 
damage the spreader.
Before  storing  for  long  periods;  Wash  the  spreader  thoroughly,  visually  inspect  the  spreader, 
grease the machine, and store in dry location.

KOMODO., (“Distributor”) warrants its ATV SEED SPREADER products (the “Products”) as follows: 

1. Limited Warranty.

 

Distributor warrants to original purchaser, providing 

Proof of Purchase

, that the Products sold hereunder will be free from 

defects in material and workmanship for a period 

of one

 year from date of purchase. If the products do not conform to this 

Limited  Warranty  during  the  warranty  period  (as  herein  specified),  Buyer  shall  notify  Distributor,  in  writing,  within  the 
warranty period, and the defects are of such type and nature as to be covered by this warranty, Distributor shall, at its own 
expense, furnish replacement products or, at Distributor's option, replacement parts for the defective products. Shipping 
and installation of the replacement Products or replacement parts shall be at Buyer's expense. 
 

2. Other Limits.

 

THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED 
TO THE IMPLIED WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Distributor 
does not warrant against damages or defects arising out of improper or abnormal use or handling of the Products; against 
defects or damages arising from improper installation, against defects in products or components. Distributor passes on to 
Buyer the warranty received (if any) from the maker thereof of such Manufacturer made products or components. This 
warranty also does not apply to Products upon which repairs have been affected or attempted by persons other than 
pursuant to written authorization by Distributor.  Fasteners are not covered in this warranty.
 

3. Exclusive Obligation.

 

THIS  WARRANTY  IS  EXCLUSIVE.  The  sole  and  exclusive  obligation  of  Distributor  shall  be  to  repair  or  replace  the 
defective Products in the manner and for the period provided above. Distributor shall not have any other obligation with 
respect  to  the  Products  or  any  part  thereof,  whether  based  on  contract,  tort,  strict  liability,  or  otherwise.  Under  no 
circumstances, whether based on this Limited Warranty or otherwise, shall Distributor be liable for incidental, special, or 
consequential damages.  
 

4. Other Statements.

 

Distributor's  employees  or  representatives'  ORAL  OR  OTHER  WRITTEN  STATEMENTS  DO  NOT  CONSTITUTE 
WARRANTIES, and shall not be relied upon by Buyer, and are not a part of the contract for sale or this Limited Warranty. 
 

5. Entire Obligation.

 

This Limited Warranty states the entire obligation of Distributor with respect to the Products. If any part of this Limited 
Warranty is determined to be void or illegal, the remainder shall remain in full force and effect.

Komodo ATV Seed Spreader Limited Warranty

K

O

M

O

D

O

  A

T

V

  A

c

c

e

s

s

o

r

i

e

s

1311 John Reed Ct.

City of Industry, CA 91745 USA

1(800)333-8889

ATVSS350.073107

Customer's Name:
Purchased From:
Date Purchased:

Model No:
Serial No:

Please, take a moment to fill in these blanks for your own records.

11

Summary of Contents for ATVSS350













Reviews: