background image

Graphic Operator Terminal / 

CHEMICAL RESISTANCE

 

 

4 CHEMICAL 

RESISTANCE 

This chapter describes the chemical resistance for the graphic operator terminal. 

4.1 Metal 

Casing 

The frame and casing material is powder-coated aluminum. This powder paint withstands 
exposure to the following chemicals without visible change: 

Chemicals 

Acetic acid 10% 

Phosphoric acid 4% 

Citric acid 10% 

Phosphoric acid 10% 

Diesel 

Sea water 

Distilled water 

Sodium chloride 2% 

Edible oil 

Sodium chloride 20% 

Fuel oil 

Euphoric acid 20% 

Hydrogen peroxide 3% 

Tap water 

The powder paint shows limited resistance to the following chemicals at room temperature: 

Chemicals

 

Butanol 

Nitric acid 3% 

Hydrochloric acid 5% 

Nitric acid 10% 

Isopropyl alcohol 

Phosphoric acid 43% 

Na-hypochlorite 10% 

Turpentine 

Note:

 If exposure to any of the above chemicals is demanded, it is recommended to first test the 

chemical on an invisible spot of the metal casing. 

The powder paint shows little or no resistance to the following chemicals at room temperature: 

Chemicals

 

Acetic acid, conc. 

Methyl-ethyl ketone 

Toluene 

Acetone 

Nitric acid 30% 

Trichloroethylene 

Ammonia 5% 

Phenol 

Xylene 

Ammonia, conc. 

Sodium hydroxide 5% 

97 octane unleaded 
petrol 

Ethyl acetate 

Sodium hydroxide 

98 octane leaded petrol 

 

 

13

Summary of Contents for AKI-CDT-MOD-06T





























Reviews: