background image

4

106128-2-

AA

 (A)

Kohler Co., Kohler, WI

SECURE TOILET

Assemble the bolt cap bases, washers, and nuts on the
exposed T-bolts.

CAUTION: Risk of personal injury or product
damage. 
Overtightening may cause breakage or
chipping.

Hand tighten the nuts, then tighten them an additional
1/2-turn with a wrench. If the T-bolts extend more than
1/4” from the top of the nut, cut off the excess with a hack-
saw, and file the cut edges. Wipe away any residue. Install
the bolt caps.

Fig. #7

Bolt Cap Base

Washer

Nut

Bolt Cap

INSTALL TANK

Make sure the three tank bolts extend completely through
the holes in the gasket. Set the tank onto the bowl, using
the tank bolts as a guide. Center the gasket on the inlet
of the bowl. Assemble the washers and brass nuts onto
the bolts.

Alternately tighten the three brass nuts so the top of the
tank and the top of the bowl are both level. Be sure the
brass nuts are tight enough to achieve a watertight seal.

CAUTION: Risk of product damage.
Overtightening may cause breakage or chipping of
the vitreous china bowl or tank.

Fig. #8

Tank Bolt

Gasket

Washer

Brass Nut

CONNECT SUPPLY SHUT-OFF VALVE

NOTICE: Read this section carefully before performing
these steps.

For installation of the supply shut-off valve, refer to the
installation instructions packed with the valve. Carefully
bend the tubing to fit.

Cut the end of the tubing 1/4” longer than the distance be-
tween the supply shut-off valve and the supply shank. Re-
move any burrs from the inside of the tubing.

Slip the coupling nut, compression nut, and ferrule onto
the tubing. Insert the tubing into the supply shut-off valve
and the supply shank, positioning the seal washer
(supplied) or the compression washer (not supplied), as
shown. Handtighten the coupling nut, and then tighten the
compression nut.

WARNING: Risk of property damage. Do not
overtighten any of these nuts, or you may deform
connections and cause leakage. Do not use tools
to tighten plastic nuts.

Fig. #9

Tubing

Ferrule

Supply Shank

Seal Washer

Coupling Nut

Compression Nut

Supply Shut-Off Valve

Compression Washer

Tubing

Coupling Nut

Compression Nut

Ferrule

Summary of Contents for WELLWORTH WATERGUARD K-3520









Reviews: