background image

-3-

Fig.#2

2

Remove the old gasket from the floor
and the closet flange with a putty knife.
Remove the old T-bolts and discard
them.

if the new toilet is not

installed immediately, temporarily stuff
a rag into the closet flange.

NOTICE:

T

NOTICE:

Do not use white cement or high lime content

cements to install this toilet. The expansion of cement due to

a rise in temperature may make the toilet crack or cause

damage. Kohler is not responsible for any damage caused by

installation with the use of cement.

Closet Flange

mm

67mm;

200mm
190

Fig.#3

3

Fig.#4

4

Fig.#5

5

TO INSTALL SUPPLY
SHUT-OFF VALVE

Install the supply shut-off valve so it is
200mm above the finished floor line,
and 190mm to the left of the closet
flange centerline.

The centerline of the supply shut-off
valve outlet should extend 67mm from
the finished wall. Install the supply
shut-off valve with the outlet vertical.

Supply Shut-Off Valve

Closet Flange
Centerline

190

305

200

10mm

:

5

TO INSTALL BOWL

Position the template and align with
drain hole.

Mark down the position of foot and 5
holes.

Drill holes on ground with the drill of
10mm (3/8"), then insert anchor to
holes.

Please make sure there is

no water pipe or spool under the 5
holes to be drilled.

CAUTION:

Drain Hole

3/8

10mm

TO REMOVE EXISTING TOILET

Turn off the water supply. Flush the toilet, and use a sponge
to remove the remaining water from the tank and bowl.
Disconnect the supply shut-off valve (if present), and remove
the old tank and bowl.

(

)

INSTALLATION

1326266-T01-B

Summary of Contents for VEIL K-1381T-HC









Reviews: