background image

6

116627-2-

AC

Kohler Co., Kohler, WI

TROUBLESHOOTING CHART

SYMPTOMS

PROBABLE CAUSES

CORRECTIVE ACTION

1.  Float valve

turns on/off
by itself
without
toilet being
flushed.

A. Refill tube pushed too far down in overflow

pipe.

B. No slack in flapper chain assembly, holding

flapper off seat.

C. Flush valve flapper ball worn, dirty or

misaligned with flush valve seat; or seat
corroded so flapper will not seal.

A. Attach refill tube to overflow pipe above the

water line.

B. Adjust flapper chain assembly for proper slack.

C. Inspect, clean and, if necessary, replace flapper

ball and/or seat.

2.  Float valve

continues
to run,
allowing
water to
enter tank.

A. Foreign particles lodged under the float valve

seal (located under float valve cap).

B. Float valve seal (located under float valve cap)

may be cracked or split.

A. Shut off water supply; remove float valve cap

assembly by rotating 1/8 turn counterclockwise.
Cover uncapped lower valve unit with an
inverted cup (holding it to prevent overspray),
and turn water on and off a few times. Clean
float valve seal surface (located under float
valve cap). Replace float valve cap assembly by
engaging lugs and rotating 1/8 turn clockwise.
Turn water on.
Install filter in supply line to prevent recurring
problems.

B. Replace seal.

3.  Incorrect

water level
height.

A. Valve float cup does not contain enough water

to provide required ballast.

A. During fill cycle, hold float under water a few

seconds to allow it to fill with water ballast.

4.  Long or

noisy tank
fill cycle.

A. Plugged valve inlet or supply line.

A. Perform Corrective Action 2.A.

5.  Poor flush.

A. Trapway or rim holes are obstructed.
B. Soil pipe or vent is obstructed.
C. Low water level in bowl due to refill tube being

plugged or out of overflow tube.

D. Supply shut-off valve not fully open.

A. Unclog trapway; clean rim holes.
B. Clear obstruction from soil pipe or vent.
C. Clean or straighten refill tube; attach refill tube to

overflow tube.

D. Open supply shut-off valve.

6.  Toilet

overflows.

A. Toilet trapway is obstructed.
B. Soil pipe or vent is obstructed.

A. Use plunger to unclog.
B. Clear obstruction from soil pipe or vent pipe.

7.  Toilet does

not
activate.

A. Chain is not connected to lift rod or flush valve. A. Reconnect the chain.

Summary of Contents for REVIVAL









Reviews: