Kohler rada Exact-3 B Product Manual Download

Page: 7 / 28

1057614-W2-D

Flow Control:

Rada Exact-3 B shower controls have integral flow control; no other user-

operated flow controller should be used with this shower control.

Outlet:

The outlet connector is designed to accept:

Flat-faced / flanged unions (maximum flange diameter 20 mm); use flat-faced

insert (408 71, supplied)

15 mm pipework; use compression olive (542 10).

Connections:

Rada Exact-3 B

- Inlets and Outlet: 1/2” BSP external union or 15 mm

compression (nut and olive provided).

Inlet/ Outlet Options:

INLETS: OUTLET:*

Exact-3 B

Any Configuration

bottom,

top

Products are supplied in the format shown in bold.

Standard Connections

are:

hot

left (marked red)

cold

right

(marked blue)

Outlet

top

(can be altered to bottom outlet if

required, refer to

INSTALLATION

)

Note!

Should the supplies be reversed then the shower control will not be able

to control temperature. This can be corrected by reversing the position of the

Thermostatic cartridge within the control body, as described in

INSTALLATION

All models can operate in any plane, and may be inverted if necessary for supply

pipework layout convenience, provided hot and cold pipework are connected to

the appropriately marked inlets (hot - red, cold - blue).

Summary of Contents for rada Exact-3 B





























Search results

Summary of Contents for rada Exact-3 B

Reviews:

Related manuals for rada Exact-3 B

Brands by name

Popular brands

Kohler rada Exact-3 B, Product Manual

Search results

Summary of Contents for rada Exact-3 B

Reviews:

Related manuals for rada Exact-3 B

Brands by name

Popular brands