background image

-9-

0 C

o

CONSUMER RESPONSIBILITIES

If you live in a hard water area, make certain that the holes in
the toilet rim are kept clean to ensure proper bowl flushing.
Toilet bowl cleaners should be used at least once a week.
Use a long-handled brush to clean the rim holes, and to clean
as far into the trap as possible to prevent mineral deposits
from forming.

Most toilet bowl cleaners are not harmful to the vitreous china
surface of the toilet bowl. Please follow the bowl cleaner
manufacturer is instructions carefully.

Do not use in-tank cleaners. Products containing
chlorine (calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause leakage
and property damage.

Kohler Company shall not be responsible or liable for any
damage to these tank fittings caused by the use of cleaners
containing chlorine (calcium hypochlorite).

Do not use abrasive cleaners or solvents.

WARNING: Risk of property or product damage.

'

Please do not use hard materials (like

scouring pad) to clean product surface, especially the
product logo.

CAUTION:

CAUTION: Don t use any cement while installing
the toilet.

WARNING: Risk of product damage.

Heat expansion of the toilet may damage

the feet of the toilet. Kohler will not be responsible for
any damage because of using cement.

Do not throw into the toilet what is easy to block it,
such as newspaper, paper pilch, sanitary towel.
Do not bump the vitreous china with great force to
prevent it from damaging and leaking.
Do not use the product in the water below 0 C.

o

1098366-T01-D

Summary of Contents for PERSUADE K-3654T-CW










Reviews: