background image

CAUTION : Risk of product damage. 

Do not lift the bath by the piping or pump, or use the piping or pump  

for structural support of the bath.

Bath Installation

Prepare the Bath

□  When removing bath. Do not lift bath by pipe work. Inspect for any possible damage that may have occurred 

 

  in transit.

□  Insert the drain tailpiece into the trap. Make sure the bath is level. Use silicone to seal between drain and trap.
□  Seal the joint between the bath rim and the finished tiled wall using silicone sealant.
□  Ensure adjustable feet are fitted through holes drilled in support frame.
□  Locate bath in proposed position. The protect film originally covering your spa has been recovered to fit its 

 

  equipment, therefore, carefully protect its surface during installation.

□  Make sure the bath is level (and resting on all support blocks).

□  Install the drain to the bath according to the drain manufacturer’s instructions. Do not connect the trap 

 

  at this time.
□  To adjust the height, loosen the nut A, adjust the height by tightening the nut B, and then tighten the nut A.
□  Position the bath on the support, adjust the level.

Bath rim must be fully supported.

560-600 mm

Bath

Pipe

Adjust and lock to recommended height.

Adjust the nut A to lock/unlock 

the adjustable feet.

Adjust the height of the bath 

by tightening the nut B.

A

B

Bath must be installed level on all top edges.

Plumbing Installation

NOTE : 

An access panel will simplify future maintenance.

□  Connect the drain to the trap according to the drain manufacturer’s instructions.
□  Open the hot and cold water supplies, and check the supply connections for leakage.
□  Run water into the bath, and check the drain connections for leakage.

CAUTION : Risk of product damage.

 Ensure a watertight seal on the bath drain.

Kohler Co. 

1241693-X2-B

Summary of Contents for K-97260X

























Reviews: