Koeppl Luchs HYDRO LHR-2 Operating Manual Download Page 34 | Manualshive

Page: 34 / 48

Koeppl Luchs HYDRO LHR-2 Operating Manual Download Page 34

Page 34

Version 02-2010

LHR-2

Maintenance

Maintenance

Besides complying with operating regulations applicable to the tractor, it is equally important to
pay due attention to the following instructions for care and maintenance!

Caution!

•

Care and maintenance work may only be carried out when the engine is switched off and
the spark plug cap has been pulled off!

•

Always change the oil in the hydraulic drive, gearbox and engine promptly.

•

Fluids escaping under high pressure (fuel, hydraulic oil) can penetrate the skin and cause
serious injuries. Therefore, always consult a doctor - risk of infection!

•

Dispose of oils, fuels, batteries, brake fluids, coolants and filters separately and properly!

•

The fitting of tyres requires sufficient knowledge and correct fitting tools!

•

Tighten the wheel nuts again after 8 hours of operation.

•

Always disconnect the earth strap from the battery when working on the electrical system!

•

Spare parts must correspond at least to the technical requirements specified by the manu-
facturer! This is ensured, for example, by the use of original spare parts!

1.

Engines

Please follow the engine manufacturer’s detailed operating manual!

2.

Hydraulic drive

Always change the oil in the power take-off gearbox, hydraulic drive and engine promptly.

Caution!

•

The hydraulic system is under high pressure!

•

Due to the risk of injury, use suitable aids when searching for leaks!

•

It is essential to switch the engine off and to secure the tractor against rolling away when
working on the hydraulic system!

•

Ensure absolute cleanliness when working on the hydraulic system!

•

Dirt and moisture must not be allowed to get into the system.

•

Open connections should always be sealed with a protective cap, even if only opened for a
short time.

•

Check hydraulic hoses at regular intervals for damage and aging and replace them if neces-
sary!

•

Damaged pipes and hoses must be replaced immediately!

«
...
32
33
34
35
36
...
»

Summary of Contents for Luchs HYDRO LHR-2

















































Reviews:

No comments