background image

 

MAINTENANCE ADVICE 

  The frame and upholstery are sensitive to knocks and scratches, so be careful, especially when 

transporting the Flexxo. 

  Always use a rain canopy when it is raining. The upholstery is water resistant but water can 

nonetheless seep in through the seams and cause damage. Should your Flexxo become wet, 
use a soft cloth to wipe off excess moisture and then allow it to dry fully. Leave the upholstery to 
dry in the dark. Some discoloration of the upholstery is possible, especially if it gets wet. 

  The upholstery can be easily cleaned using a moist cloth and if necessary mild soap. Always 

treat the whole surface and let the material dry in the dark. 

  If necessary, you can wash the upholstery. Read the washing instructions on the labels. In the 

seat are two boards. These should be removed before washing (the boards can be taken out by 
undoing the Velcro on the back of the seat). Remove dirt. Wash in lukewarm water (no hotter 
than 30 degrees). Rinse well to remove any soap residue. Do not use washing powder. Lie flat 
and let dry in the dark. Smooth away as many wrinkles as possible from the upholstery. Do not 
use a dryer/spin cycle. 

  You can dry or clean the Flexxo frame using a soft towel. 

  Although our materials are selected for their colourfastness, some decolourisation can occur due 

to climatological influences. You can reduce this by keeping the Flexxo out of direct sunlight or 
covering the Flexxo with a white sheet. Salt residues from transpiration from your hands can 
cause the upholstery to become greasy and sallow. 

  Regularly spray the moving parts of the Flexxo frame with Teflon spray or silicon spray to ensure 

their continued smooth operation. Regularly spray the axles with Teflon spray or silicon spray. 
Never use oil, grease or other oil-based lubricants because these actually attract dirt and dust. 

  Always remove salt and sand immediately. 

  Prevent overloading of the frame! The maximum weight allowed is 18 kilograms. 

  When you have a flat tyre you can fix it by using a puncture repair kit. If necessary, replacement 

inner tubes can be ordered from your specialist baby store. 

 
We advise you to carry out the above maintenance regularly so as to ensure maximum enjoyment 
from your Flexxo. Damage caused by not following these instructions is not covered under the 
warranty. 
 
Should you want to make use of our service network, please contact your dealer with proof of 
purchase and warranty. If a part needs to be replaced, use only parts supplied by Koelstra. 
 
We wish you much enjoyment with your Flexxo Plus! 
 
KOELSTRA 
 
Sales Promotion  

 

Summary of Contents for FLEXXO PLUS RG20124E









Reviews: