Function: SIREN SOUND WHEN ARMING THE SYSTEM WITH SENSOR BYPASS
.
FN=6
4
SN=1
SN=2
SN=2
The siren sound is turned OFF.
The siren will sound for 0.3 seconds.
Function: TYPE OF SIREN. THE POWER OF SOUND ON ARMING AND DISARMING.
FN=6
5
SN=1
SN=2
SN=
3
SN=
3
The horn type siren (speaker with coil impedance at least 4 Ohm) with the maximum sound power adjusted.
The horn type siren (speaker with coil impedance at least 4 Ohm) with the sound power reduced by 2
.
The horn type siren (speaker with coil impedance at least 4 Ohm) with the sound power reduced by 4
.
The input is used for signal '
LUGGAGE COMPARTMENT (
–)
'
with opening option. It is available to open the luggage compartment using appropriete remote's
button in armed state with no alarm. The system waits for ID card for 10 seconds. If the system finds no ID card, turns ON alarm signals. The sensors are
bypassed. After luggage compartment closing the system returns to regular armed state.
SN=1
SN=2
The siren sound is turned OFF
.
The siren makes confirmation beeps.
SN=
4
SN=
5
The horn type siren (speaker with coil impedance at least 4 Ohm) with the sound power reduced by 8
.
Standard electronic siren
.
Function: SIREN ACTION WHEN ARMING OR DISARMING CAR ALARM SYSTEM.
FN=66
E
S
FUNCTION
G
N
6
Ib
.
P
G
N
6
Ib
.U
P
S
G
N
6
Ib
.U
FN=99
Function: RESTORE DEFAULT FACTORY SETTINGS.
Restore default factory settings and the default PIN code.
SN=1
The direction indicators are flashing and siren sounds if any zone of the sensor is triggered
.
The sensor is turned OFF
.
The sensor is turned OFF
.
The sensor is turned OFF
.
The direction indicators are flashing and siren sounds if alarm (inner) zone of the sensor is triggered
. The direction indicators are flashing only if pre-alarm
(outer) zone of the sensor is triggered.
SN=3
SN=3
SN=6
SN=3
SN=4
Function: CHANGING THE PIN.
FN=88
Melody 3 (the h
orn type siren is used
).
SN=3
Function: WARNING MELODY ON TRIGGERING OF THE BUILT-IN SHOCK SENSOR PRE-ALARM ZONE.
Melody 1 (the h
orn type siren is used
).
Melody 2 (the h
orn type siren is used
).
FN=67
SN=1
SN=2
SN=2
Direction indicators flashes.
SN=
3
Direction indicators flashes with 5 second delay.
SN=4
Direction indicators flashes with delay pre-set by computer.
The direction indicators are flashing only if the sensor is triggered.
The direction indicators are flashing only if the sensor is triggered.
The direction indicators are flashing only if the sensor is triggered.
SN=2
SN=2
SN=2
Function: ALARM SYSTEM OPERATION WHEN BUILT-IN SHOCK SENSOR IS TRIGGERED
'
', '
'
.
(FOR GN6Ib.P
GN6Ib.UPS ONLY)
Function: ALARM SYSTEM OPERATION WHEN BUIT-IN
ULTRASONIC
SENSOR IS TRIGGERED
'
’, '
'
.
(FOR GN6Ib.
U
GN6Ib.UPS ONLY)
Function: ALARM SYSTEM OPERATION WHEN BUILT-IN
TILT
SENSOR IS TRIGGERED
'
'
.
(FOR GN6Ib.UPS ONLY)
The direction indicators are flashing and siren sounds if the sensor is triggered
.
The direction indicators are flashing and siren sounds if the sensor is triggered
.
The direction indicators are flashing and siren sounds if the sensor is triggered
.
Function: ALARM TRIGGER MEMORY
.
FN
=77
FN
=7
5
FN
=78
SN=1
SN=1
SN=1
FN=71
FN=72
FN=73
The car alarm system shows the cause of alarm (see chapter 9) when Fn71, FN72 or FN73 is entered. Direction indicators makes 5 series of flashes and
the number of flashes in each series correspond to the cause of alarm trigger. The FN71 shows the latest trigger and the FN72, FN73 shows previous
triggers accordingly).
Direction indicators makes no flash.
Function: DIRECTION INDICATOR OPERATION WHEN
ARMING OR DISARMING CAR ALARM SYSTEM.
FN=68
SN=1
Melody 4 (the h
orn type siren is used
).
SN=4
The direction indicators are flashing only if any zone of the sensor is triggered.
SN=5
SN=
3
The siren makes confirmation beeps. While disarming the siren will make 4 beeps if the alarm was triggered before the system was disarmed.
SN=2
The input is used for
signal 'ENGINE BONNET (
–
)
.
Function: ALARM SYSTEM ACTIONS ON THE IGNITION TURNING ON WITH THE SYSTEM IS ARMED
.
(FOR GN6Ib.UPS ONLY)
'
'
FN=56
SN=1
The alarm system immobilizes the engine, starts alarming.
If was no perimeter (doors, engine bonnet, luggage compartment) violation during the system is armed and is no violation at the ignition turning ON
moment the system regards it as the actions of the automatic engine start module and allows to start the engine. Otherwise the system immobilizes the
engine, starts alarming and returns to regular armed state. The perimeter is under monitoring with the engine is running, however the sensors are bypassed.
When the 20 second time after the ignition turning ON is elapsed and ignition state remains the same, the system sends to GSW1G code "Engine started".
If the perimeter is violated the system immobilizes the engine, starts alarming and returns to regular armed state. If the ignition is turned OFF and
20 second time is elapsed the system sends to GSW1G code "Engine stopped" and returns to the regular armed state.
Function: INPUT 'CONDITION2'.
FN=
54
SN=1
SN=2
The input is used for signal 'CONDITION2'.
The input is used for the override button.
SN=
3
Not used.
Function:
INPUT
'
DOORS (
–)’
(FOR GN6Ib.UPS ONLY).
'
'
FN=
5
5
SN=1
The input is used for signal '
LUGGAGE COMPARTMENT (
–)
'
.
SN=4
SN=5
The automatic learning (in accordance with chapter 7.3).
The postponed a
utomatic learning (in accordance with chapter 7.3).
