Kodak 3140 Repairing Instructions Download Page 6

Page: 6 / 16

MISCELLANEOUS PUBLICATION

18JUL97 – XP3210-006

Replacing the DC-DC CONVERTER

Possible damage from electrostatic discharge.

ESD

[1] Remove the four SCREWS and WASHERS from

the back of the KEYPAD. Keep the SCREWS and
WASHERS.

[2] Carefully lift the KEYPAD OVERLAY/

CIRCUIT BOARD ASSEMBLY out of the
KEYPAD.

Caution

Be careful not to damage the wires and ribbon cables
attached to the ASSEMBLY.

[3] Check the KEYPAD OVERLAY/BOARD

ASSEMBLY for damage.

Note

There are plastic STANDOFFS between the KEYPAD
OVERLAY and CIRCUIT BOARD. If only one or two
STANDOFFS are broken, continue with the next step.

If more than two of the plastic STANDOFFS are
broken, you should replace the KEYPAD OVERLAY/
CIRCUIT BOARD ASSEMBLY. Advance to the
procedure Replacing the KEYPAD OVERLAY/
CIRCUIT BOARD ASSEMBLY on page 13.

H027_2516AC

SCREWS

H027_2516ACA

H027_2517AC

H027_2517ACA

KEYPAD OVERLAY

CIRCUIT BOARD

PLASTIC
STANDOFFS

Summary of Contents for 3140

















Search results

Summary of Contents for 3140

Reviews:

Related manuals for 3140

Brands by name

Popular brands

Kodak 3140, Repairing Instructions

Search results

Summary of Contents for 3140

Reviews:

Related manuals for 3140

Brands by name

Popular brands