Kobold KME Operating Instructions Manual Download Page 14

14

Operating instructions for KME flow meter for compressed air and gases

4.1.1  Switch and pulse outputs

Switch and pulse outputs are NOT potential-free and include internal pull-down resistors (fig.10)

V+

GND

GND

10k

10k

OUT 1

OUT 2

Fig. 10 

Switch/pulse output

4.2  Bus output (projected)

4.2.1  M-Bus (Meter Bus) (projected)

The M-Bus (Meter Bus) is a field bus for recording consumption data. Transmission runs serially 

on a reverse polarity protected two-wire line. The KME flow meter as M-Bus slave requires a sep-

arate supply voltage. There is no prescribed specific topology (line or star) for the wiring. Normal 

phone cable of type J-Y(St)Y Nx2x0.8 mm can be used. The max. cable length per segment 

(primary addressed) is 250 m (3.28 ft).

The table below shows the structure of the consumption data sent by the transmitter:

Header

68

Start of the telegram

4F 4F

L-field (length)

68

Second starting signal

08

C-field (RSP_UD)

XX

A-field (address)

Start user data

72

CI-field (variable data structure)

XX XX XX XX

Identification number

A5 16

Manufacturer (0x16A5 … EUE)

01

Version

09

Medium (9 … compressed air)

XX

Access number (consecutive)

00

Status

00 00

Signature

Data record 1: Volume flow

05

DIF (32 bit real)

3E

VIF (volume flow in m³/h)

XX XX XX XX

Cur. measured value

Data record 2: temperature

05

DIF (32 bit real)

5B

VIF (temperature in °C)

XX XX XX XX

Cur. measured value

Data record 3: Mass flow

05

DIF (32 bit real)

53

VIF (mass flow in kg/h)

XX XX XX XX

Cur. measured value

Data record 4: Consumption meter status

05

DIF (32 bit real)

16

VIF (volumes in m³)

XX XX XX XX

Cur. consumption value

Data record 5: Flow velocity

05

DIF (32 bit real)

7F

VIF (manufacturer-specific in m/s)

XX XX XX XX

Cur. measured value

Data record 6: Volume flow

04

DIF (32 bit integer)

3B

VIF (volume flow in 10-³ m³/h)

XX XX XX XX

Cur. measured value

Data record 7: temperature

04

DIF (32 bit integer)

59

VIF (temperature in 10-² °C)

XX XX XX XX

Cur. measured value

Data record 8: Mass flow

04

DIF (32 bit integer)

51

VIF (mass flow in 10-² kg/h)

XX XX XX XX

Cur. measured value

Data record 9: Consumption meter status

07

DIF (64 bit integer)

13

VIF (volumes in 10-³ m³)

XX XX XX XX 

XX XX XX XX

Cur. consumption value

Data record 10: Flow velocity

04

DIF (32 bit integer)

7F

VIF (manufacturer-specific in 10-² 

m/s)

XX XX XX XX

Cur. measured value

end user data

XX

Checksum

16

End of telegram

Summary of Contents for KME





























Reviews: