USER MANUAL CENTRAL HEATING STATION TYPE
REV.12.06.2017
Figure 1.13 – pressure in the heating installation
temperature is 60°C.
9.2.8
Graphic context - Service submenu
In the
Service
submenu, various functioning parameters of the central heating station can be viewed/ changed/ checked. This
submenu can be accessed only by service personnel authorised by
9.3
Central heating station startup
To startup the station press J5(
POWER)
key
Choosing the functioning mode winter/ summer
By pressing
J7
key (
) you can change the functioning mode winter/ summer.
S5/S6
will be activated.
Adjusting temperature on the thermal circuit
The adjustment of temperature is done by pressing
decrease temperature. Simbol S9(
) will flash
Adjusting water temperature on the hot water circuit
The adjustment of temperature is done by presing
decrease temperature. Simbol S10(
)
9.4
Functioning as waste hot water station (WHW)
The station can function as WHW in both seasons
The WHW request has priority over the heating request in the „winter” mode.
The station can function as instant WHW or as accumulation boiler WHW (the boiler is
functioning of the station as an accumulation boiler WHW station please contact an authorised service company.
In intant regime, the minimum flow of hot water detected by the station is
For confort in using the station as a WHW station we recommend to exploit the station at a flow of approximately
When the station functions with low flows, the station functions continuously at the minimum charge as long as the hot water
temperature is under the threshold limit of
burner is closed and a new burning will happen when the hot water temperature is lower than the limit of
When the station functions with high flows, the hot water temperature will be the opposite of the hot water flow, but lower than
the set temperature.
With instant WHW configuration on request the
authorized service company.
This function allows the delivery of hot water as soon as possible, while keeping the boiler hot.
starts when the hot water temperature is equal to the set hot water temperature; the boiler stops when the hot water
temperature is 8°C ( fixed value) higher than the set hot water temperature. If the water heated in t
within one hour, the
CONFOR
T function is automatically deactivated.
9.5
Functioning as heating station (HS)
The station functions in this mode when „winter” season is selected. For the selection of the type of heating installation (f
radiators) please contact an authorised service company.
If a thermoregulator is connected to the electronic board, the stations functions in thermal mode only when the surrounding
temperature is lower than the set temperature in the thermoregulator
9.6
Preset functions related to station safety
1.
Anti-freezing protection function.
If the temperature in the installation drops below
minimum charge until the temperature reaches
2.
Post-circulation of the hot water and heating pump function.
BURNING
state.
Advantages:
a) it prevents the water from becoming stationary at high temperatures inside the heat switch. In
are reduced significantly
b) it prevents water from boiling inside the heat switch
These advantages have as result the protection of the heat switch.
3.
Pump anti-blocking system and three
If the station did not go through a burning cycle in the last
this time the three-way valve is also activated and deactivated.
4.
Post-ventilation
After each station stop, the ventilator still functions for some time to evacuate completely the burning gases out of the station
and also the water vapours they contain
which cools down partially, are protected.
5.
“Legionella” bacteria prevention function
This function is active
for the functioning of the station as accumulation boiler WHW.
When hot water is prepared in the boiler, the ANTILEGIONELLA function is actived automatically. This function implies that
a week the temperature of the water in the boiler is kept at the value of 65°C.
9.7
Setting additional functions
Setting additional functions is done only in the
USER MANUAL CENTRAL HEATING STATION TYPE C32SPV24MEFB; C32SPV31MEFB; C22SPV23MEF
ure in the heating installation 1,6 bar, central heating station is set on winter mode
submenu
various functioning parameters of the central heating station can be viewed/ changed/ checked. This
submenu can be accessed only by service personnel authorised by KOBER SRL Vaduri Branch.
key fig.1.5.
Choosing the functioning mode winter/ summer
you can change the functioning mode winter/ summer. This can be viewed on the display, symbol
Adjusting temperature on the thermal circuit
The adjustment of temperature is done by pressing
J1
and
J2
keys. Press
J1
to increase temperature and
will flash intermitent.
Adjusting water temperature on the hot water circuit
The adjustment of temperature is done by presing
J3
and
J4
keys. Press
J3
to increase temperature and
) will flash intermitent.
hot water station (WHW)
The station can function as WHW in both seasons – winter and summer.
The WHW request has priority over the heating request in the „winter” mode.
The station can function as instant WHW or as accumulation boiler WHW (the boiler is
functioning of the station as an accumulation boiler WHW station please contact an authorised service company.
In intant regime, the minimum flow of hot water detected by the station is 2.4 l/min
For confort in using the station as a WHW station we recommend to exploit the station at a flow of approximately
When the station functions with low flows, the station functions continuously at the minimum charge as long as the hot water
ture is under the threshold limit of 63°C. When the hot water temperature reaches the mentioned limit of
burner is closed and a new burning will happen when the hot water temperature is lower than the limit of
h high flows, the hot water temperature will be the opposite of the hot water flow, but lower than
With instant WHW configuration on request the
CONFORT
function can be activated/ deactivated.
This function allows the delivery of hot water as soon as possible, while keeping the boiler hot. If the function is active, the boiler
starts when the hot water temperature is equal to the set hot water temperature; the boiler stops when the hot water
higher than the set hot water temperature. If the water heated in t
T function is automatically deactivated.
Functioning as heating station (HS)
The station functions in this mode when „winter” season is selected. For the selection of the type of heating installation (f
radiators) please contact an authorised service company.
If a thermoregulator is connected to the electronic board, the stations functions in thermal mode only when the surrounding
temperature is lower than the set temperature in the thermoregulator.
Preset functions related to station safety
f the temperature in the installation drops below 9°C, the system turns on the heating at
minimum charge until the temperature reaches 30°C.
circulation of the hot water and heating pump function.
The post-circulation cycle
starts only if the system is not in
becoming stationary at high temperatures inside the heat switch. In
b) it prevents water from boiling inside the heat switch in the post-heat interval.
These advantages have as result the protection of the heat switch.
system and three-way valve.
If the station did not go through a burning cycle in the last
24h
, the pump will be started for
12 seconds
way valve is also activated and deactivated.
still functions for some time to evacuate completely the burning gases out of the station
and also the water vapours they contain. In this way, both the ventilator control electric circuit and the primary heat switch,
ected.
revention function
for the functioning of the station as accumulation boiler WHW.
When hot water is prepared in the boiler, the ANTILEGIONELLA function is actived automatically. This function implies that
a week the temperature of the water in the boiler is kept at the value of 65°C.
Setting additional functions is done only in the "
Service
" menu. Please contact an authorised service company.
12 of 19
central heating station is set on winter mode, set value of hot water
various functioning parameters of the central heating station can be viewed/ changed/ checked. This
This can be viewed on the display, symbol
to increase temperature and
J2
respectively to
to increase temperature and
J4
respectively to
purchased separately). For the
functioning of the station as an accumulation boiler WHW station please contact an authorised service company.
For confort in using the station as a WHW station we recommend to exploit the station at a flow of approximately 7-8 l/min.
When the station functions with low flows, the station functions continuously at the minimum charge as long as the hot water
When the hot water temperature reaches the mentioned limit of 63°C, the
burner is closed and a new burning will happen when the hot water temperature is lower than the limit of 60°C.
h high flows, the hot water temperature will be the opposite of the hot water flow, but lower than
function can be activated/ deactivated. Please contact an
If the function is active, the boiler
starts when the hot water temperature is equal to the set hot water temperature; the boiler stops when the hot water
higher than the set hot water temperature. If the water heated in this way is not consumed
The station functions in this mode when „winter” season is selected. For the selection of the type of heating installation (floor or
If a thermoregulator is connected to the electronic board, the stations functions in thermal mode only when the surrounding
the system turns on the heating at
starts only if the system is not in
the
becoming stationary at high temperatures inside the heat switch. In this way, calcareous deposits
12 seconds
to avoid its blocking. In
still functions for some time to evacuate completely the burning gases out of the station
In this way, both the ventilator control electric circuit and the primary heat switch,
When hot water is prepared in the boiler, the ANTILEGIONELLA function is actived automatically. This function implies that once
Please contact an authorised service company.
