background image

rev A 

MNL-7178.docx 

15 of 19 

7

 

W

ARRANTY

 

Kobelt Manufacturing Co. Ltd. (“Kobelt”) warrants the 

Products and Parts manufactured by 

Kobelt to be free from defects in workmanship or material and that said products are 
designed mechanically and functionally to perform to specifications.  

This warranty is effective providing: 

 

The equipment is used within the intended operating conditions and in accordance with 
Kobelt recommendations 

 

The equipment is installed according to equipment diagrams, specifications and 
recommendations which Kobelt has provided 

This warranty becomes invalid if the factory supplied serial number has been removed or 
altered on the product. This warranty does not cover cosmetic damage or damage caused by 
an act of God, accident, misuse, abuse, negligence or modification of any part of the product. 
This warranty does not cover damage due to improper operation or maintenance, connection 
to inappropriate equipment or attempted repair by anyone other than an authorized Kobelt 
representative. 

Upon identification of a potential issue or defect with a Kobelt Product or Part, the Warranty 

Applicant (“Applicant”) must immediately contact Kobelt and describe the issue in writ

ing, by 

letter, fax, email or other electronic conveyance. Kobelt will then assess the cause of the 
defect, and determine warranty applicability and appropriate remediation.  

If any part is found to be defective, Kobelt will replace said part FOB the Kobelt factory 
provided that any such defective part is returned by the Buyer with freight and applicable 
forwarding charges prepaid by the Buyer. 

Kobelt’s sole obligation to the Applicant will be to 

repair or replace the defective part with same or similar product, to a maximum value of the 
list price of the product or part. The Kobelt warranty does not cover labour charges, travel or 
any other associated expenses. 

All Products and Parts manufactured by Kobelt, are subject to a warranty against 

manufacturer’s d

efects in materials or workmanship for a period of two (2) years from the 

date of purchase.  

Kobelt will be responsible for all Products or Parts sold by Kobelt but manufactured by 3

rd

 

party manufacturing companies. However, these products and parts are subject to applicable 
3

rd

 party warranties, and may not be the same as the Kobelt warranty.  

 

Summary of Contents for 7178 Series




















Reviews: