Knox MedVault Hardware Installation Manual Download Page 2

OPE-MVHDWR-0202-H 

 

 

 

 

 

         

The Knox Company ▪ MedVault

®

 

 ▪ ii 

 

 

Copyright 

®

 2019 by The Knox Company. All rights reserved.  

 

The Knox Company, the Knox logo and all other Knox Company product or service names are 
registered trademarks or trademarks of the Knox Company. 

Restricted Rights Legend 

U.S. GOVERNMENT RESTRICTED RIGHTS. UNPUBLISHED—RIGHTS RESERVED 
UNDER THE COPYRIGHT LAWS OF THE UNITED STATES. Use, duplication, or disclosure 
is subject to restrictions set forth in the FAR Section 52.227-14 Alt. III(g)(3), FAR Section 
52.227-19, DFARS 252.227-7014(b), or DFARS 227.7202, as amended from time to time. 

The Knox Company 

1601 W. Deer Valley Road 
Phoenix, AZ 85027 USA 
(800) 552-5669 General Information, (866) 566-9269 Electronic Support, (623) 687-2290 Fax 

 
Contacting the Knox Company, Limited Warranty and Order Terms 
and Conditions 

You can access the Knox Company web site at http://knoxbox.com. From this web site, you can 
obtain general information about the company, customer support,  products and career 
opportunities. You can also register and log into the system to obtain software updates and new 
manuals.  Your installation and use of the product is subject in all respects to Knox’s limited 
warranties for products and Knox’s Order Terms and Conditions which are also available at 
http://knoxbox.com. 
 

Important Information for MedVault 

WiFi

 Units 

FCC NOTICE  

The RF module contained within this device complies with the rules set forth in Part 15 by the 
Federal Communications Commission. 
Operation is subject to the following conditions: 
1. This device may not cause harmful interference. 
2. This device must accept any interference received, including interference that may cause 
undesired operation. 
3. An approved antenna must be directly coupled to the module's RP-SMA connector. 
4. The module must not be modified in any way. Coupling of external circuitry must not bypass 
the provided connectors. 
5. The antenna used for this transceiver must not be co-located or operated in conjunction with 
any other antenna or transmitter. 
Any changes or modifications could void the user's authority to operate the equipment. 
 
This Class B digital apparatus complies with Canadian ICES-003. 
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 
 
This Device Contains: FCC ID: R68MTCHDRCT, IC ID: 3867A-MTCHDRCT or FCC ID: 
YOPGS2100MIE, IC ID: 9154A-GS2100MIE. Refer to product label to determine which 
module is installed.

Summary of Contents for MedVault













Reviews: