DANGER
Product specifications ......................................................... 1
Warnings .............................................................................. 1
Symbols .............................................................................. 1
Power tool safety ................................................................ 2
Slide compound miter saw safety ....................................... 3
Electrical requirements and safety ...................................... 3
Pre-assembly ...................................................................... 4
Carton contents .................................................................. 5
Know your slide compound miter saw ................................. 6
Glossary of terms .............................................................. 7
Assembly ........................................................................... 8
Adjustments ...................................................................... 11
Operation ........................................................................... 14
Maintenance ...................................................................... 21
Troubleshooting guide ........................................................ 21
Parts list ............................................................................. 22
Schematic .......................................................................... 24
Parts list and diagram (motor) ........................................... 25
PRODUCT SPECIFICATIONS
MOTOR
Power Source:
120V AC, 60Hz, 15 Amp
Arbor Shaft Size:
5/8 in.
Speed (no load):
2400 RPM (No load)
Electric Brake:
Yes
Double Insulated:
Yes
TABLE OF CONTENTS
1
WARNINGS
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals
known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber.
Your risk
from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemical:
work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to
fiter out microscopic particles.
WARNING
SYMBOLS
WARNING ICONS
Your power tool and its Instruction Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to, and/or in
-
struct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool
better a. safer. Shown below are some of the symbols you may see.
SAFETY ALERT:
Precautions that
involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety
goggles or safety glasses with side shields.
READ AND UNDERTAND INSTRUCTION MANUAL: To
reduce the risk of injury, user and all bystanders must read
understand instruction manual before using this product.
KEEP HANDS AWAY FROM BLADE: Failure to
keep your hands away from the blade will result
in serious personal injury.
SUPPORT AND CLAMP WORK
DANGER: Indicates an inminently
hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially
hazardou situation which, if not avoided, could result
in dead or serious injury.
CAUTION: Indicates a potentially hazardou
situation which, if not avoided, may result in minor or
moderate injury.
CAUTION: Used without the safety alert
symbol indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
BLADE
Diameter:
10 in.
Arbor:
5/8 in.
Dust port. (o.d.):
1-1/4 in.
Net weight:
23.18 kg
MITER SAW
Rotating Table:
Miter Detent Stops:
0, 15, 22.5, 31.6, 45º R & L
Bevel Positive Stops:
0, 33.9, 45º R & L
WARNING
To avoid electrical hazards, fire hazards or damage to the tool, use proper circuit protection. This tool is wired at
the factory for 110-120 Volt operation. It must be connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker.
To avoid shock or fire, replace power cord immediately if it is worn, cut or damaged in any way.
Before using your tool, it is critical that you read and understand these safety rules. Failure to follow these rules could result in
serious injury to you or damage to the tool.
WARNING
CAUTION
CAUTION
CUTTING CAPACITY
Crosscut:
3-3/8 in. x 11-23/32 in.
Miter 45° R & L:
3-3/8 in. × 7-25/32 in.
Bevel 45º R & L:
1-5/8 in. x 11-23/32 in.
Compound 45°:
1-5/8 in. x 7-25/32 in.
Steel Plate:
7/32 in. thickness
Square Steel Box:
2 in. (1/8 in. thickness)
Round Steel Tube:
2 in. (1/8 in. thickness)
WEAR RESPIRATOR AND HEARING PROTECTION:
Always wear respiratory and hearing protection.
Summary of Contents for KN M-2502N
Page 53: ...www knova com mx...
