KNOVA KN DP-2500N, Manual, Page: 2 / 40

1
Product specifications .......................................................... 1
Power tool safety ................................................................ 1
Drill press safety ................................................................. 2
Electrical requirements and safety ...................................... 3
Accessories and attachments ............................................. 3
Tools needed for assembly .................................................. 4
Carton contents .................................................................. 4
Know your drill press ........................................................... 5
Glossary and terms ........................................................... 6
Assembly and adjustments ............................................... 6
Operation .......................................................................... 12
Maintenance ...................................................................... 15
Troubleshooting guide ....................................................... 16
Parts list ............................................................................ 17
Exploded view ................................................................... 18
PRODUCT SPECIFICATIONS
POWER TOOL SAFETY:
1. READ and become familiar with the entire instruction
manual. LEARN the tool’s application, limitations and
possible hazards.
2. KEEP GUARDS IN PLACE and in work order.
3. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose them
to rain. Keep work area well lighted.
4. DO NOT use power tools in the presence of flammable
liquids or gases.
5. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
6. KEEP CHILDREN AWAY. All visitors should be kept a
safe distance from work area.
7. DON’T FORCE THE TOOL. It will do the job better and
safer at the rate for which it was designed.
8. USE THE RIGHT TOOL. Do not force tool or attachment
to do a job for which it was not designed.
9. WEAR PROPER APPAREL. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other jewellery, that
may get caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering to contain
long hair.
10. WEAR A FACE MASK OR DUST MASK. Drilling
operation produces dust.
11. DISCONNECT TOOLS before servicing; when changing
accessories such as blades, bits, cutters, and the like.
12. REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in OFF position before plugging in.
13. USE RECOMMENDED ACCESSORIES. Consult the
Operator’s Manual for recommended accessories. The
use of improper accessories may cause serious injury.
TABLE OF CONTENTS
WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals
(known to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• Lead based paints
• Crystalline silica from bricks, cement and other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals, work in a well-ventilated area and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
BEFORE USING THIS DRILL PRESS
Safety is a combination of common sense, stay alert and
knowing how to use your drill press.
W A R N I N G
To avoid electrical hazards fire hazards
or damage to the tool, use proper circuit protection.
This tool is wired at the factory for 110-120 Volt operation. It
must be connected to a 110-120 Volt / 15 Ampere time delay
fuse or circuit breaker. To avoid shock or fire, replace power
cord immediately if it is worn, cut or demaged in any way.
Before using your tool, it is critical that you read and under-
stand these safety rules. Failure to follow these rules could
result in serious injury to you or damage to the tool.
GENERAL SAFETY INSTRUCTIONS
W A R N I N G
To avoid mistakes that could cause
serious injury, do not plug the drill press
in until you have read and understood the following.
1/2 in.
(12.7mm).
5
(620 ~ 3100 RPM)
Chuck size:
Speed:
Motor: 120V, 60 Hz
Horsepower :
2/3 HP
(max. developed)
45º right or left
5 in. (127mm)
Table tilt:
Spindle
travel:
Throat:
2 in. (50.8mm)
Laser guide:
Yes