Knick SensoGate WA 132 Series User Manual Download Page 41

Page: 41 / 48

Accessories / Spare Parts

SensoGate WA 132

ZU 0733

Adapter for Free Hose Connection,

with electrical limit switches, PP housing

This adapter is used for operating the SensoGate WA 132 via multi-

plug without the Unical 9000 (X) controller and the corresponding

media connection.

ZU 0734

Adapter for Free Hose Connection,

without electrical limit switches, PP housing

This adapter is used for operating the SensoGate WA 132 via multi-

plug without the Unical 9000 (X) controller and the corresponding

media connection.

ZU 0739

Bellows

The bellows (for liquid-electrolyte sensors only) protects the fitting

beneath the sensor pressure chamber against pollution and wear.

Immersion Tube, Long

Material: PTFE, on request

Immersion Tube, Short

Material: PTFE, on request

Immersion Tubes

Long

Short

Summary of Contents for SensoGate WA 132 Series

















































Search results

Summary of Contents for SensoGate WA 132 Series

Reviews:

Related manuals for SensoGate WA 132 Series

Brands by name

Popular brands

Knick SensoGate WA 132 Series, User Manual

Search results

Summary of Contents for SensoGate WA 132 Series

Reviews:

Related manuals for SensoGate WA 132 Series

Brands by name

Popular brands