Knick Portavo 908 MULTI User Manual Download Page 28 | Manualshive

Page: 28 / 76

background image

28

pH

Calimatic Calibration

(Automatic calibration with specification of the buffer solution used)

1) Select the number of calibration points and the buffer set as shown in the table

below and press the Start softkey.

Cal points

Auto | 1-point | 2-point | 3-point

Buffer set

Mettler-Toledo

2.00/4.01/7.00/9.21

Knick CaliMat

2.00/4.00/7.00/9.00/12.00

Ciba

2.06/4.00/7.00/10.00

NIST technical

1.68/4.00/7.00/10.01/12.46

NIST standard

1.679/4.006/6.865/9.180

Hach

4.01/7.00/10.01/12.00

WTW

2.00/4.01/7.00/10.00

Hamilton

2.00/4.01/7.00/10.01/12.00

Reagecon

2.00/4.00/7.00/9.00/12.00

DIN 19267

1.09/4.65/6.79/9.23/12.75

User buffer 1

configurable via Paraly SW 112 software

2) Immerse the sensor in the 1st/2nd/3rd buffer solution and press Continue

(repeat this step for each calibration point).

3) Finally, the calibration data will be displayed.

You can Apply or Discard these values.

Note: To abort calibration, you can press meas at any time.

pH Calibration

1)  In measuring mode, press the Menu softkey.
2)  Select “Calibration” and confirm by pressing enter.
3)  Select the desired “Calibration mode” and confirm by pressing enter.
4)  The “TAG” menu allows the sensor TAG to be edited.

To do so, set “TAG” to On in the configuration menu
(default setting: Off).

5) Perform the selected calibration as described on the following pages.

Follow the instructions on the display.

Note: Calibration is not possible when the device is connected via USB with the
Paraly SW 112 software.

Calibration

«
...
26
27
28
29
30
...
»

Summary of Contents for Portavo 908 MULTI













































































Reviews:

No comments

Related manuals for Portavo 908 MULTI

Brand: Kawai Pages: 5

Brand: Jata hogar Pages: 12

Brand: Halcyon Pages: 36

Brand: X-Rite Pages: 45

Brand: X-Rite Pages: 22

Brand: janitza Pages: 128

LaserHybrid SB 360i

Brand: Fronius Pages: 104

Brand: PCB Piezotronics Pages: 16

fieldscout TDR 100

Brand: Spectrum Techniques Pages: 20

WD-35606-00, WD-35606-05

Brand: Oakton Pages: 10

Brand: Fuji Electric Pages: 85

Brand: FASAR ELETTRONICA Pages: 2

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brand: Apogee Pages: 18

Brand: T&D Pages: 31

Sonic-Pro S6A Series

Brand: Blue-White industries Pages: 2

Brand: FMT Swiss AG Pages: 24

Brand: MFJ Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands