Knick Portavo 904 User Manual Download Page 45

Page: 45 / 54

Concentration determi-

nation

-01- NaCl

0 – 26 wt% (0 °C / 32 °F) ... 0 – 28 wt% (100 °C / 212 °F)

-02- HCl

0 – 18 wt% (–20 °C / –4 °F) ... 0 – 18 wt% (50 °C / 122 °F)

-03- NaOH 0 – 13 wt% (0 °C / 32 °F) ... 0 – 24 wt% (100 °C / 212 °F)
-04- H

0 – 26 wt% (–17 °C /–1.4 °F) ... 0 – 37 wt% (110 °C / 230 °F)

-05- HNO

0 – 30 wt% (–20 °C / –4 °F) ... 0 – 30 wt% (50 °C / 122 °F)

-06- H

94 – 99 wt% (–17 °C/–1.4 °F) ... 89 – 99 wt% (115 °C / 239 °F)

-07- HCl

22 – 39 wt% (–20 °C / –4 °F) ... 22 – 39 wt% (50 °C / 122 °F)

-08- HNO

35 – 96 wt% (–20 °C / –4 °F) ... 35 – 96 wt% (50 °C / 122 °F)

-09- H

28 – 88 wt% (–17 °C /–1.4 °F) ... 39 – 88 wt% (115 °C / 239 °F)

-10- NaOH 15 – 50 wt% (0 °C / 32 °F) ... 35 – 50 wt% (100 °C / 212 °F)

Specifications

Connections

1 x DIN socket, 8 pins for analog sensors

2 x 4-mm socket for separate temperature detector

1x M8 socket, 4 pins, for Memosens lab cable

1 x micro USB-B for data transmission to PC

Portavo 904X:

Be sure to observe the safety instructions when using the

USB port.

Display

LCD STN 7-segment display with 3 lines and icons

Sensoface

Status display (friendly, neutral, sad)

Status indicators

For battery condition, logger

Notices

Hourglass

Keypad

[on/off], [cal], [meas], [set], [



], [



], [STO], [RCL], [clock]

Data logger

With up to 5000 memory locations

Recording

Manual, interval- or event-controlled

Communication

USB 2.0

Profile

HID, driverless installation

Usage

Data exchange and configuration via Paraly SW 112 PC software

Specifications

Summary of Contents for Portavo 904























































Search results

Summary of Contents for Portavo 904

Reviews:

Related manuals for Portavo 904

Brands by name

Popular brands

Knick Portavo 904, User Manual

Search results

Summary of Contents for Portavo 904

Reviews:

Related manuals for Portavo 904

Brands by name

Popular brands