Knick Portavo 904 OXY User Manual Download Page 36 | Manualshive

Page: 36 / 50

background image

36

Error and Status Messages

Error messages are indicated as “ERROR …” on the display. Information on the sensor
condition is indicated by the “Sensoface” icon (friendly, neutral, sad) possibly accom-
panied by an info message (“INFO …”).

Sensoface (the “smiley” icon) provides
information on the sensor condition (main-
tenance request). Measurement can still be
performed. After a calibration, the corre-
sponding Sensoface icon (friendly, neutral,
sad) is shown together with the calibration
data. Otherwise, Sensoface is only visible in
measuring mode.

The most important error messages and
“Sensoface” info messages are shown on
the inside of the protective cover. A com-
plete list of messages and their meanings is
provided in the following tables.

Example of a “Sensoface” message:
INFO 1 (cal timer expired)

Example of an error message:
ERROR 1 (value out of range)

«
...
34
35
36
37
38
...
»

Summary of Contents for Portavo 904 OXY



















































Reviews:

No comments

Related manuals for Portavo 904 OXY

Brand: ABB Pages: 8

Brand: Jennov Pages: 50

Brand: Teac Pages: 148

Brand: IFM Pages: 25

Brand: Campbell Pages: 16

Brand: Magnum Energy Pages: 3

Kotron 805 series

Brand: Magnetrol Pages: 36

Brand: Magnescale Pages: 104

Brand: Magnescale Pages: 44

Brand: T&D Pages: 2

Brand: T&D Pages: 2

Brand: Underground Magnetics Pages: 48

Brand: Yamaha Pages: 84

Brand: Pangea Pages: 2

Brand: Magene Pages: 80

Brand: Solartron Mobrey Pages: 34

Brand: Magnescale Pages: 2

Brand: Datakom Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands