KNEGT 504G3 Series Operation Manual Download

Page: 33 / 111

504G3

SERIES TRACTOR OPERATION MANUAL

and rear tires to leave ground. Turn front and rear tires about 3 minutes in two

directions, instantly drain out the cleaning liquid. Meanwhile dismantle inlet oil

filter or lifter to clean, refill new oil to transmission system, lifter and front axle as

per specified after reinstall well.

3. Drain out coolant and after clean cooling system by water.

4. Clean diesel filter and air cleaner.

5. Check front toe-in, clutch, and the free path of brake, adjust it if necessary.

6. Check and fasten all outside bolts, nuts and screws.

7. Check the nozzle and valve clearance.

8. Check the working of electrical system.

9. Refill lubricant grease to each part of the tractor.

Summary of Contents for 504G3 Series
















































































































Search results

Summary of Contents for 504G3 Series

Reviews:

Related manuals for 504G3 Series

Brands by name

Popular brands

KNEGT 504G3 Series, Operation Manual

Search results

Summary of Contents for 504G3 Series

Reviews:

Related manuals for 504G3 Series

Brands by name

Popular brands