KNECHT HV 203 Operating Instructions Manual Download Page 61

Page: 61 / 70

Turn clamping lever (9-37/1) to “Closed” position.

The knife is now locked.

Swivel the grinding plate with the clamped knife
forward to the grinding belt.

9.2.8 Basic function of the HV 262 locking mechanism

NOTE

The locking disc has several locking positions.
The first two positions are U-shaped, all
subsequent positions are V-shaped.

The two U-shaped locking positions are used to
adjust the knife on the grinding belt and to grind
the burr.

The V-shaped locking positions are used for
convex grinding of the knife.

0 = adjustment position (9-38/1)
1 = grinding position (9-38/2)
2 – 11 = convex grinding (9-38/3)

NOTE

Every grinding process is started with
adjustment position “0”.

Locking lever

Locking disc

Hand wheel

Star handle

Figure 9-37

Locking the knife on the grinding

plate

9. Operating the HV 262

Figure 9-38

Locking disc

Figure 9-39

Overview of locking mechanism

Summary of Contents for HV 203







































































Search results

Summary of Contents for HV 203

Reviews:

Related manuals for HV 203

Brands by name

Popular brands

KNECHT HV 203, Operating Instructions Manual

Search results

Summary of Contents for HV 203

Reviews:

Related manuals for HV 203

Brands by name

Popular brands