KMC Controls 61 Series Manual Download Page 21

Page: 21 / 52

45’

Rotary Harrow

SEPT 2008

2.4 WING ASSEMBLY

1 @ 1/4 UNF GREASE NIPPLE

1 @ HINGE BOLT, REAR FLIP OVER

1 @ SPACER, FLIP OVER CONNECTION

2 @ 1 UHMW FLATWASHER

1 @ 1 SAE FLATWASHER

1 @ 7/8 UNC NYLON LOCKNUT

1 @ WASHER, FLIP OVER HINGE

NOTE:

1. RIGHT WING SHOWN. LEFT WING

SAME PARTS EXCEPT

“(

LEFT)

”

FOR THOSE PARTS MARKED AS

“(

RIGHT)

”.

2. LEFT PARTS HAVE –

SUFFIX.

1 @ 7/8 X 6 1/4 SAFE PIN

1 @ HITCH PIN CLIP

1 @ 1 X 4 1/2 G8 BOLT

1 @ LONG BUSHING (1 25/32 LG)

1 @ 1 X 5 G8 BOLT

2 @ PLASTIC BUSHING (1 1/2 ID X 2 1/2 OD

1 @ SHORT GROOVED BUSHING (1 17/32 LG)

1 @ 1 G8 UNITORQUE HUT

1 @ 1 X 5 G8 BOLT

2 @ PLASTIC WASHER

1 @ NYLON LOCKING NUT

2 @ 1 G8 NUT

1 @ ROD SUPPORT WASHER

1 @ 1 HARDENED WASHER

ITEM

PART NUMBER

DESCRIPTION

QTY

51025

WING STIFF ARM (RIGHT)

51028

WING FRONT BEAM (RIGHT)

51026

WING LONG BRACE

080

034

SLIDE, LH TOOL

080

035

SLIDE, RH TOOL

51034

WING TRANSPORT SUPPORT

080

053

WING TOOL CATCHER

51115

WING FLIP OVER (RIGHT)

081

009

WING CASTER ASSEMBLY

51015

SPACER, FLIP OVER CONNECTION

51097

TOOL LEVER. LONG STROKE

51098

TENSION ROD, LONG STROKE PL

51004

BUSHING, TENSION ROD

1 @ 1/4 UNF GREASE NIPPLE

4 @ 1/2 X 2 G8 BOLT

4 @ 1/2 G8 UNITORQUE NUT

1 @ 1 X 7 1/2 UNC G8 BOLT

2 @ PLASTIC BUSHING (1 1/2 ID X 2 1/2 OD)

1 @ LONG BUSHING (1 25/32 LG)

1 @ 1 G8 UNITORQUE NUT

4 @ 5/8 X 2 UNC G8 BOLT

4@ 5/8 G8 LOCK FLANGE NUT

THREAD FASTENING COMPOUND

2 @ 1/2 UNC X 4 9/16 X 7 1/4 U

BOLT

4 @ 1/2 UNC NUT

4 @ 1/2 LOCKWASHER

1 @ HINGE BOLT, REAR FLIP OVER

2 @ 1 UHMW FLATWASHER

1 @ 1 SAE FLATWASHER

1 @ 7/8 UNC NYLON LOCKNUT

1 @ WASHER, FLIP OVER HINGE

4 @ 5/8 X 2 UNC G8 BOLT

4@ 5/8 G8 LOCK FLANGE NUT

THREAD FASTENING COMPOUND

2 @ 3/4 X 1 1/2 UNC G8 BOLT

2 @ 3/4 G8 UNITORQUE NUT

4 @ 3/4 X 6 UNC G8 BOLT

4 @ 3/4 UNC UNITORQUE G8 NUT

NOTE: USE LOCK

TITE ON ALL NUTS

11"

Summary of Contents for 61 Series





















































Search results

Summary of Contents for 61 Series

Reviews:

Related manuals for 61 Series

Brands by name

Popular brands

KMC Controls 61 Series, Manual

Search results

Summary of Contents for 61 Series

Reviews:

Related manuals for 61 Series

Brands by name

Popular brands