background image

Faulty temperature sensor

(short circuited)

Faulty temperature sensor

(cannot be detected)

Cooker's electrical fuse was blown 

Bad power connection or no power

Pressure control fails

Steam release handle not in

sealing position

Float valve obstructed by the lid

locking pin

Float valve silicone ring worn-out

Food debris on the float valve

silicone seal

Lid not closed properly

Food debris attached to the sealing 

ring 

Sealing ring damaged

No sealing ring

Float valve in the popped-up

position 

Sealing ring not installed properly

Replace the float valve silicone seal

Add water according to the recipe

Close the lid completely

Turn the release handle to the

sealing position

Inspect the power cord to ensure a

good connection, check the power

outlet is active.

Contact Kmart. Product is faulty.

After cooking, cycle completes, leave

the cover on for 5 more minutes.
Adjust  dry-rice and  water ratio

according  to recipe

Adjust  dry-rice and  water

ratio  according to  recipe 

Position the sealing ring well
Press the float valve lightly

downwards
Use the steam release handle to

reduce the internal pressure. Open

the lid after the pressure is

completely released.
Press the float valve lightly with a

pen or chopstick.
Install the sealing ring
Replace the sealing ring

Clean the sealing ring

Open then close the lid again

Clean the float valve silicone seal

Too litter water

Faulty pressure sensor

Contact an electrician to check the 

mains power outlet socket in your home.

Mains voltage is too low

Contact Kmart. Product is faulty.

Contact Kmart. Product is faulty.

Contact Kmart. Product is faulty

Contact Kmart. Product is faulty.

E8 code

EL code

E2 code

E1 code

Cover opened prematurely

Steam comes out from 

exhaust valve non-stop            

Rice half cooked or too

hard           

Rice too soft

Too much water

Display remains blank

after connecting the 

power cord           

All LEDs flash

with a code

appearing on 

screen

Float valve unable to rise            

Steam leaks from float 

valve for over 2 minutes

Steam leaks from the 

side of the lid

Difficult to open the lid

Pressure exists inside the cooker

Float valve stuck at the popped-up

position  

Difficult to close the lid

Possible Reason

The cases in the following tables do not always indicate a faulty cooker. Please 

examine the cooker carefully before contacting Kmart.

Problem

Solution

Too little food or water in inner pot

17

Troubleshooting

Summary of Contents for anko MY-CS6002WP1






















Reviews: