Klutch NT18G Operator'S Manual Download Page 9

9 — English

ASSEMBlY

INSTAllING GRINDING WHEEl

See Figure 2, page 12.

DANGER:

Use ONLY Type 27 depressed center grinding wheels 
(such as the one provided with this product). NEVER 
 attach a Type 1 straight or cut-off wheel to this angle 
grinder. Use for any other purpose is not recommended 
and creates a hazard, which will result in serious injury.

DANGER:

Never attach a wood cutting or carving blade of any type 
to this grinder. It is only designed for grinding and sand-
ing. Use for any other purpose is not recommended and 
creates a hazard, which will result in serious injury.

WARNING:

Thoroughly inspect a new grinding wheel before you 
install it on the grinder.

• Tap lightly around the wheel using a wooden hammer.
• Listen  carefully  to  the  resulting  sounds.  Places  with 

fissures or cracks will result in a different sound.

Do not use a wheel containing fissures or cracks. 
When you install a new grinding wheel, carry out a no 
load revolution test of approximately one minute with 
the grinding wheel facing a safe direction, i.e., away from 
people or objects.

  Depress the spindle lock button and rotate the clamp nut 

until the spindle locks. 

 NoTE: 

To prevent damage to the spindle or spindle lock, 

always allow motor to come to a complete stop before 
engaging spindle lock. 

  Loosen and remove the clamp nut

 

from the spindle. Do 

not remove the disc flange.

  Make sure the flats on the bottom of the disc flange are 

engaged with the flats on the spindle.

  Place the grinding wheel over the spindle. 

WARNING:

Always install a grinding wheel with the depressed center 
against the disc flange. Failure to do so will cause the 
grinding wheel to crack when tightening the clamp nut. 
This could result in serious personal injury because of 
loose particles breaking off and being thrown from the 
grinder. Do not overtighten.

  Thread the clamp nut

 

on the spindle with the flat side of 

the nut facing up. 

  Fit the raised, small diameter portion of the clamp nut

 

 

into the hole in the wheel and finger tighten.

  Depress the spindle lock button and rotate the wheel 

clockwise until the spindle locks in position.

  Tighten the clamp nut

 

securely with the wrench provided. 

Do not overtighten.

INSTAllING THE SIDE HANDlE

See Figure 3, page 12.

WARNING:

The side handle must always be used to help prevent 
loss of control and possible serious injury.

The side handle can be installed on the top, left, or right side 
of the grinder, depending on operator preference. 

  Insert the side handle into the desired operating position.

  Turn the side handle clockwise to securely tighten. 

oPERATIoN

WARNING:

Do not allow familiarity with this product to make you 
careless. Remember that a careless fraction of a second 
is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to 
comply with ANSI Z87.1, along with hearing protection. 
Failure to do so could result in objects being thrown into 
your eyes and other possible serious injuries.

Type 27 

 OK TO use

Type 1 

 dO nOT use

Summary of Contents for NT18G

























Reviews: