Klutch NT18G Operator'S Manual Download Page 5

5 — English

ANGlE GRINDER SAFETY WARNINGS

 

Position the cord clear of the spinning accessory. 

If 

you lose control, the cord may be cut or snagged and your 

hand or arm may be pulled into the spinning accessory.

 

Never lay the power tool down until the accessory 

has come to a complete stop. 

The spinning accessory 

may grab the surface and pull the power tool out of your 

control.

 

Do not run the power tool while carrying it at your 

side.

 Accidental contact with the spinning accessory 

could snag your clothing, pulling the accessory into your 

body.

 

Regularly clean the power tool’s air vents.

 The motor’s 

fan will draw the dust inside the housing and excessive 

accumulation of powdered metal may cause electrical 

hazards.

 

Do not operate the power tool near flammable 

materials.

 Sparks could ignite these materials.

 

Do not use accessories that require liquid coolants. 

Using water or other liquid coolants may result in 

electrocution or shock.

KICKBACK AND RElATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged 

rotating wheel, backing pad, brush or any other accessory. 

Pinching or snagging causes rapid stalling of the rotating 

accessory which in turn causes the uncontrolled power tool 

to be forced in the direction opposite of the accessory’s 

rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by 

the workpiece, the edge of the wheel that is entering into the 

pinch point can dig into the surface of the material causing 

the wheel to climb out or kick out. The wheel may either jump 

toward or away from the operator, depending on direction 

of the wheel’s movement at the point of pinching. Abrasive 

wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect 

operating procedures or conditions and can be avoided by 

taking proper precautions as given below.

 

Maintain a firm grip on the power tool and position 

your body and arm to allow you to resist kickback 

forces. Always use auxiliary handle, if provided, for 

maximum control over kickback or torque reaction 

during start-up.

 The operator can control torque 

reactions or kickback forces, if proper precautions are 

taken.

 

Never place your hand near the rotating accessory. 

Accessory may kickback over your hand.

 

Do not position your body in the area where power 

tool will move if kickback occurs. 

Kickback will propel 

the tool in direction opposite to the wheel’s movement 

at the point of snagging.

 

Use special care when working corners, sharp edges. 

etc. Avoid bouncing and snagging the accessory. 

Corners, sharp edges or bouncing have a tendency to 

snag the rotating accessory and cause loss of control or 

kickback.

 

Do not attach a saw chain woodcarving blade or 

toothed saw blade. 

Such blades create frequent 

kickback and loss of control.

SAFETY WARNINGS SPECIFIC FoR GRINDING 
oPERATIoNS

 

Use only wheel types that are recommended for your 

power tool and the specific guard designed for the 

selected wheel. 

Wheels for which the power tool was not 

designed cannot be adequately guarded and are unsafe.

 

The guard must be securely attached to the power 

tool and positioned for maximum safety, so the least 

amount of wheel is exposed towards the operator. 

The guard helps to protect operator from broken wheel 

fragments and accidental contact with wheel.

 

Wheels must be used only for recommended 

applications. For example: do not grind with the side 

of cut-off wheel. 

Abrasive cut-off wheels are intended for 

peripheral grinding, side forces applied to these wheels 

may cause them to shatter.

 

Always use undamaged wheel flanges that are of 

correct size and shape for your selected wheel. 

Proper wheel flanges support the wheel thus reducing the 

possibility of wheel breakage. Flanges for cut-off wheels 

may be different from grinding wheel flanges.

 

Do not use worn down wheels from larger power tools. 

Wheel intended for larger power tool is not suitable for 

the higher speed of a smaller tool and may burst.

SAFETY WARNINGS SPECIFIC FoR SANDING 
oPERATIoNS

 

Do not use excessively oversized sanding disc paper. 

Follow manufacturers recommendations, when 

selecting sanding paper. 

Larger sanding paper extend-

ing beyond the sanding pad presents a laceration hazard 

and may cause snagging, tearing of the disc or kickback.

SAFETY WARNINGS SPECIFIC FoR 
PolISHING oPERATIoNS  

 

Do not allow any loose portion of the polishing bonnet 

or its attachment strings to spin freely. Tuck away or 

trim any loose attachment strings. 

Loose and spinning 

attachment strings can entangle your fingers or snag on 

the workpiece.

SAFETY WARNINGS SPECIFIC FoR WIRE 
BRUSH oPERATIoNS

 

Be aware that wire bristles are thrown by the brush 

even during ordinary operation. Do not overstress the 

wires by applying excessive load to the brush.

 The wire 

bristles can easily penetrate light clothing and/or skin.

 

If the use of a guard is recommended for wire 

brushing, do not allow any interference of the wire 

wheel or brush with the guard. 

Wire wheel or brush 

may expand in diameter due to work load and centrifugal 

forces.

Summary of Contents for NT18G

























Reviews: