Klutch 48410 Owner'S Manual Download Page 6

 

Page 6 of 14 

 

WELDING CART USE AND CARE 

 

Store the Welding Cart out of reach of children and other untrained persons. 

 

Use only accessories that are recommended by the manufacturer for your model. Accessories 
that may be suitable for one product may become hazardous when used on another product. 

 

Maintain labels and nameplates on the Welding Cart. 

 

Maintain a safe working environment. Make sure there is adequate surrounding workspace. DO 
NOT use this product in a damp or wet location. 

 

Make certain caster wheels are locked in position when the Welding Cart is stationary. 

 

DO NOT exceed the maximum weight capacity for the entire Welding Cart. DO NOT exceed the 
maximum weight capacity for each individual Shelf. 

 

Use on a flat, level surface capable of supporting the Welding Cart and the products within it. 

 

Load tools evenly. As much as possible, distribute the weight of all tools stored in the Welding 
Cart evenly. 

 

DO NOT use the Welding Cart as a step stool or ladder. Never sit, stand, or climb on the Welding 
Cart. 

 

Avoid tipping. DO NOT overload or over-stack the Welding Cart. Overloading can damage 
drawers and casters and could possibly result in tipping and personal injury. Over-stacking can 
result in tools or other objects sliding or falling from the Welding Cart and could result in damaged 
tools and/or personal injury. 

 

Be aware of dynamic loading. Dropping or bouncing a load may briefly create excess load 
causing product damage, severe personal injury, and/or death. 

 

Inspect Welding Cart before loading. If you see any damage to load bearing surfaces remove all 
items from that surface. DO NOT use a damaged surface. 

 

DO NOT modify the Welding Cart in any way. DO NOT use for applications other than what is 
described in this manual. 

Summary of Contents for 48410















Reviews: