background image

41

41

Operation instructions controller

      

 

Pressing the three buttons ( 

  

    ) below the display

simultaneously, acknowledges the fault message.

8.3 Overpressure

      

 

When this message appears on the display, the pressure downstream from the high pressure pump is too high. 
The high pressure pressure switch is triggered at a pressure of 150 bar, and reduces the speed of the motor. If the 
pump speed has dropped enough for the pressure switch to turn on again at 135 bar, the control unit saves this 
frequency and the humidifier returns to operating mode. This saved frequency is stored as the maximum frequen-
cy until the fault has been rectified or the control unit has been reset. Since the Klingenburg humidifier continues 
to operate and the nominal frequency is thus also shown in the display, an overpressure fault is displayed.

An overpressure fault can be caused by several factors:

  the maximum frequency is set too high.
  the atmomiser nozzles may be dirty, which leads to increased flow resistance. This leads to higher pressure 

for the same amount of water.

Conduit pressure fault
Actual frequency

Target frequency
Actual frequency

Fault message after the set tripping time.

Overpressure message is displayed!

L e i t u n g s d r k s t ö r !
R   I s t f r e q . :   0 0 H z

S o l l f r e q u . :   5 6 H z
R   I s t f r e q . :   5 6 H z

Motor overheating

The motor in the pump station is protected against damage from overheating. A thermal contact inside the motor 
sends a signal to the control unit, causing the motor to switch off and triggering a fault message.

Service indicator

The Service message appears if the recommended oil change intervals have been exceeded. The first message 
appears after the first 50 operating hours and then every 1000 operating hours after that. Pressing the Enter key 
(

) can suppress the message in order to return to the frequency display. The Service message can be reset in 

programming mode once the oil change has been carried out. If the Service message is not reset, it will reappear 
in the display.

Error codes

      

 The seven possible faults are displayed by the two-digit error 
code in the second line of the display.

  M o t o r   t e m p !
S   I s t f r e q . :   0 0 H z

          S e r v i c e

H a r d w a r e   e r r
            E : x x !

Summary of Contents for CERTO





















































Reviews: