background image

www.klever-mobility.com

www.klever-mobility.com

48

49

Bicycle parts 

Please note! The recommended tyre pressure is indicated 
on the sidewall of the tyres (Schwalbe Super Moto 2,0 – 
4,0 bar; 30 – 55 Psi).
Please note! Regularly check the correct tyre pressure 
and pressurise your tyres if necessary. The tyre uses an 
inner tube with Schrader valve. So, you can check and 
inflate the tyre at any gas station.
Caution! Above or below, never exceed the recommended 
air pressure range. The tyre and the tube can be damaged 
and this may lead to sudden loss of air with risk of an 
accident. Too low tyre pressure causes higher rolling 
resistance. As a consequence, this reduces the range of 
your battery.

Disassembly, repair & assembly of the tyres

Regularly check the tyres for cracks and for the height of its 
thread pattern height. In case you find that cracks or sharp 
objects have damaged the fabric of the tyre or the thread 
pattern is no longer sufficient, replace the tyres. If in doubt, ask 
your Klever dealer who can verify the tyre and replace it.
In the case of a flat tyre, you do as follows:
•  Always use plastic tyre levers.
•  Remove the wheel as described above.
•  Deflate the tyre and push a tyre lever underneath the tyre

bead opposite of the valve and lift the tyre over the rim 
flange.

•  Push the second tyre lever underneath the tyre bead in a 

distance of 10 cm. from the first one (image 72). If the tyre is
still very tight around the rim, then use a third tyre lever as 
well.

•  Now, you can lift the tyre over the whole circumference of 

the rim with the help of one of the levers. The inner tube can
be removed.

•  In case the leak cannot be found easily, hold the inflated 

inner tube into a bucket of water and look for the rising air
bubbles.

•  Repair the tube according to the instructions on the repair

kit or if necessary, replace it. In case of replacement, make 
sure you buy the correct size inner tube.

•  Check the inside of the tyre for sharp objects that could have

caused the puncture and remove them. If the fabric of the 
tyre is damaged, replace the tyre too. Start the mounting of 
the inner tube by inserting the valve into the valve hole in 
the rim and inflate the tube with very little air pressure until 
it is wrinkle-free. 

Bicycle parts 

•  Now mount the inner tube without any creases underneath

the tyre (image 73).

•  Starting opposite to the valve, lift the tyre bead over the 

flange of the rim and pull it deep into the rim. Lift the rest of
the tyre by hand over the rim’s shoulder. Use no tyre levers, 
as this may damage the inner tube.

•  Push the valve a little back into the tyre, so that the bead of

the tyre is correctly seated in the rim.

•  Pull the valve back again and inflate the inner tube to the

recommended tyre pressure.

7.8 Luggage carrier and transport of 

luggage

Your X Speed has a robust and durable aluminium luggage 
carrier (image 74). The carrier is compatible with the majority of 
all standard panniers, and you can use it in conjunction with an 
extensive range of accessories. Please note, the maximum load 
capacity of the luggage carrier is 25 kg.

Please note! When transporting luggage make sure that you 
do not exceed the total maximum permitted weight of 150 kg., 
being the combination of speed p c luggage.
Caution! The additional weight of luggage on your rear 
carrier changes the handling of the bike and extends the 
braking distance as well.

7.9 Anti-theft protection

Your Speed Pedelec comes with a motor lock and immobiliser 
combined with an acoustic alarm system. The battery can only 
be removed from its docking station by unlocking the battery 
lock with the key (see section 6.5.3 Removal and mounting of the 
battery pack). We recommend to also use a robust and high-quality 
chain lock in order to be able to lock the vehicle to solid fixtures.

7.10 Accessories

Useful accessories can enhance the functionality and comfort 
of your X Speed and they can increase your riding pleasure 
too. These accessories are available at your Klever dealer.

Please note! Accessories must be compatible with your X 
Speed speed pedelec. Incompatible accessories may influence 
and alter the riding characteristics of your bike and can lead 
to accidents. Best ask your dealer for information and advice.

Image 72

Image 73

Image 74

Summary of Contents for X Alpha 45





































Reviews: